|
|
Sponsored Content
Operating Systems
AIX
How to detect the network cable status with c programming on AIX
Post 302556024 by DGPickett on Friday 16th of September 2011 10:58:47 AM
09-16-2011
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
My system ( Solaris 2.6, Entrerprise 250 ) shows lot of connections in TIME_WAIT status against service
localhost.8007 and
localhost.45221
What are these services and where can I get the cross references.
I have checked up in /etc/services and there is no such entry.
Infact... (5 Replies)
Discussion started by: shibz
5 Replies
2. Solaris
Hi All,
I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot.
While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies
3. AIX
Hello ... I am newbie and will be very grateful for any help. I need a serial console cable for my AIX boxes (seems we have lost the one we had!). However I am confused about the one one to order - UK based if possible. I wonder if anyone can point me at a specific one or the exact spec i need to... (0 Replies)
Discussion started by: tim441
0 Replies
4. IP Networking
Hi, I am trying to implement a server-client socket communication. My server and clients are in different PCs. During communications if the ethernet cable is removed from the server side it shows broken pipe due to unable to write on the socket. I want to know how to check whether the ethernet... (0 Replies)
Discussion started by: JagadishB
0 Replies
5. Shell Programming and Scripting
I write a script which will stop an application, then restart it.
Sometimes it is succesful, sometimes not.
The problem is, when stop the application, some ports are still listenning (or not released). When start the application, it reports that ports are used, and can't continues.
I use... (1 Reply)
Discussion started by: rdcwayx
1 Replies
6. Shell Programming and Scripting
Hi there,
I'm driven crazy by a new problem.
It seems very complex to me and I see no way to come around.
In my script, I receive the path to a tgz file and I want to output the md5 sum of the file inside the tgz. I want a way to detect if tar fails.
I'm using the following command
tar... (7 Replies)
Discussion started by: chebarbudo
7 Replies
7. Programming
Hi,
I want to code TCP/IP client/server in linux application capable to fastly detect ethernet cable disconnection in any condition.
So I have activate SO_KEEPALIVE options and set TCP_KEEPCNT, TCP_KEEPIDLE and TCP_KEEPINTVL to 1.
When I disconnect ethernet cable I have the following... (5 Replies)
Discussion started by: jeje_clb
5 Replies
8. AIX
Hi.
I have 2 libraries (overland + data domain).
My AIX 7.1 detect all "rmt" of the overland but none of the data domain.
I have the Atape driver 12.3.9.
During cfgmgr, I have this message :
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support... (2 Replies)
Discussion started by: stephnane
2 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. Post Here to Contact Site Administrators and Moderators
ssssssssssss (0 Replies)
Discussion started by: sampathenjoy
0 Replies
LEARN ABOUT FREEBSD
liebert
LIEBERT(8) NUT Manual LIEBERT(8) NAME
liebert - Driver for Liebert contact-closure UPS equipment NOTE
This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8). SUPPORTED HARDWARE
This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver. EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5). BUGS
This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable. You may have to build another cable with DTR connected through to the UPS for it to work. There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a fundamental limitation of any contact-closure driver. SEE ALSO
The core driver: nutupsdrv(8) Internet resources: The NUT (Network UPS Tools) home page: http://www.networkupstools.org/ Network UPS Tools 05/21/2012 LIEBERT(8)