09-14-2011
Thank you. I know the reason, it's my usb dirve's fault. It goes wrong sometimes. After I mount it, it is writable, but some seconds later it isn't.
Another question: Why my usb drive has sdb and sdb1, while another usb drive has only sdb?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a 1 GB jazz drive. The jazz disk is used daily, both at home and at work on my Win 98 Server. So, I have to keep it in vfat format, which is fine because Linux rocks and will read it no problem. :-) However, I can't just stick the disk in the drive and open up the jazz folder in my mnt... (2 Replies)
Discussion started by: wizkid
2 Replies
2. UNIX for Dummies Questions & Answers
i'm prepping for my midterm, which i will bomb. i am scurrying to finish reading the final chapter before i get down into the review.
however, i came across something in chapter 8 - "mounting file systems" that has me really confused.
the text says the following:
then it goes on to... (2 Replies)
Discussion started by: xyyz
2 Replies
3. Solaris
Can anyone tell me how to mount the USB driver in solaris 8?
I try many time that can't to mount USB driver. It can detect the USB driver by typing #iostat -En but can't mount the driver. (1 Reply)
Discussion started by: kingsan
1 Replies
4. Linux
Is it possible to mount a disk from a non-root account?
I'm developing a Java application which executes commands in the shell using the java.lang.Runtime.exec api, which runs fine for commands ls, df, etc., but for commands mount and umount, i have problems as I need to be root to eecute these.... (8 Replies)
Discussion started by: brendan76
8 Replies
5. Solaris
In Solaris 8, when I boot to single user mode, mount a device and then reboot or init 0, the system unmount it automatically. However, in Solaris 10 it does not seem to do the same. Here is what I did:
{0} ok boot -s
# format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0.... (11 Replies)
Discussion started by: StarSol
11 Replies
6. Cybersecurity
Hello,
I'm trying to remove the need to use sudo to mount (in particular, binding).
Modifying /etc/sudoers using visudo, I have tried:
%admin ALL=NOPASSWD: /usr/bin/mount
%admin ALL=NOPASSWD: /usr/bin/umountand
%admin ALL=(ALL) NOPASSWD: /usr/bin/mount
%admin ALL=(ALL) NOPASSWD:... (5 Replies)
Discussion started by: Narnie
5 Replies
7. Hardware
Hi Gurus of Unix
Recently I install a OpenSolaris in My HP 530
In this moment want to install a USB-A to Serial Cable. Any guru can send a Link where I can use how reference.
I want to configure a Router and my PC don't have any serial Port.
My LapTOP only has USB ports. In this case I buy a... (2 Replies)
Discussion started by: andresguillen
2 Replies
8. UNIX for Dummies Questions & Answers
Hello...
I've mounted a share using standard nomenclature for the NFS mount command with the following command line:
mount -t nfs -o rw {IP address1}:/ /mnt_for_70 / {IP address2}(rw)
mnt_for_70 is a mount point I created on {IP address2}
I'm confuse and want to be sure I use the... (1 Reply)
Discussion started by: blaine.miller
1 Replies
9. Solaris
I need a help to find the patch for solaris to fix USB drivers issue on Solaris 10. The server has a PCIE card which is not recognised by the OS. I run #fmadm faulty command which report issue and recommandation to apply the new patch. I got a reference to //sun.com/msg/PCIEX-8000-6D but... (0 Replies)
Discussion started by: espengongo
0 Replies
10. HP-UX
Hi Folks,
Could anyone please assist me with the what could be the scenarios to test the file system mount/umount performance check in HPUX.
Thanks in advance,
Vaishey (5 Replies)
Discussion started by: Vaishey
5 Replies
LEARN ABOUT FREEBSD
devfs.rules
DEVFS.RULES(5) BSD File Formats Manual DEVFS.RULES(5)
NAME
devfs.rules -- devfs configuration information
DESCRIPTION
The devfs.rules file provides an easy way to create and apply devfs(8) rules, even for devices that are not available at boot.
For devices available at boot, see devfs.conf(5).
The format of this file is simple. Empty lines and lines beginning with a hash sign ('#') are ignored. A line between brackets denotes the
start of a ruleset. In the brackets should be the name of the ruleset and its number, separated by an equal sign.
Other lines are rule specifications as documented in devfs(8), in the section Rule Specification. These lines are prepended with ``rule''
and are passed to devfs(8) by the startup scripts of the system. It is important to put path elements that contain glob(3) special charac-
ters between quotes.
Rulesets should have a unique name and number.
All rules that follow a ruleset declaration belong to that ruleset, until a new ruleset is started.
One custom ruleset has to be enabled in /etc/rc.conf, otherwise it will not be applied to the /dev file system by the default system startup
process. For example, to enable a ``localrules'' ruleset for the /dev file system, you would have to use something like this in your rc.conf
file:
devfs_system_ruleset="localrules"
FILES
/etc/defaults/devfs.rules Default devfs.rules configuration file.
/etc/devfs.rules Local devfs.rules configuration file. Rulesets in here override those in /etc/defaults/devfs.rules with the
same ruleset number, otherwise the two files are effectively merged.
EXAMPLES
To make all the partitions of da(4) devices readable and writable by their owner and the ``usb'' group, the following rule may be used:
[localrules=10]
add path 'da*s*' mode 0660 group usb
The first line declares and starts a new ruleset, with the name localrules and the number 10.
To give usbconfig(8) and libusb(3) enabled applications permission to all usb devices for their owner and the ``usb'' group, a similar rule
may be used:
add path 'usb/*' mode 0660 group usb
SEE ALSO
glob(3), devfs(5), devfs.conf(5), devfs(8)
AUTHORS
This manual page was written by Roland Smith <rsmith@xs4all.nl>.
BSD
February 21, 2010 BSD