09-08-2011
Help setting up a wireless access point
Hello,
A friend of mine just purchased a DLINK 8500AP and I'm trying to help him set up wireless internet in his house. His computers are connected to one of two switches, which are both hooked up to his DSL modem. I connected the 8500AP to one of the switches. According to the instruction manual, I need to configure the switch through a web browser. It says that DHCP is disabled by default, so I need to connect from a host on the same subnet. The default IP address of the 8500AP is 10.90.90.90/8.
Because I'm not very well versed in networking, I apologize if the steps I took do not make sense. Here's what I tried: I couldn't access the IP address in a web browser (I assume because the IP address doesn't follow that of the rest of the network). So, I tried taking one switch and only hooking up the 8500AP and my laptop. I changed my laptop's IP to 10.0.0.1 to put it on the same network. I still wasn't able to access the web sever on the wireless AP.
I would appreciate if you could point me in the right direction. Thanks a lot!
---------- Post updated at 04:21 AM ---------- Previous update was at 01:11 AM ----------
Nevermind, I was able to get into the configuration page. It turns out that DHCP was enabled. I used Angry IP Scanner to find the local IP address and was able to access it through my browser.
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am trying to configure Solaris 10 for Internet Connection.
I have a PC (Celeron 1.7Ghz, 512 MB RAM, Gigabyte 8LD Motherboard).
The Wireless Telephone Specs are:
TATA Indicom Walky.
Further product details are as follows ( I did not understand most of what it says. I have
given... (0 Replies)
Discussion started by: priteshugrankar
0 Replies
2. IP Networking
Hi,
I am trying to configure Solaris 10 for Internet Connection.
I have a PC (Celeron 1.7Ghz, 512 MB RAM, Gigabyte 8LD Motherboard).
The Wireless Telephone Specs are:
TATA Indicom Walky.
Further product details are as follows ( I did not understand most of what it says. I have given it... (0 Replies)
Discussion started by: priteshugrankar
0 Replies
3. IP Networking
Hi guys,
I want to setup AP using an NETGEAR WGR614 54 Mbps 802.11g Wireless Router
The router works fine, but I don't have internet access. I will describe the structure of the net to explain it:
I have one server (Free BSD 7) with 2 LAN PCI cards:
re0 - it is connected to my ISP
... (2 Replies)
Discussion started by: sitemap
2 Replies
4. Ubuntu
I am doing a site survey for possibly a new contract and am using kismet for analysis. The are several buildings and was wondering if there was a utility that will map out the location of access points o report and to help out with analyses. Is there anything in the open source community that can... (0 Replies)
Discussion started by: metallica1973
0 Replies
5. IP Networking
In the OSI model there is a thing called SAP. I can't find information about it...
The only thing i found is this:
Does anybody know where i can find more explanations about SAP????
thanks in advance! (2 Replies)
Discussion started by: Sandia_man
2 Replies
6. Ubuntu
Hii
i have installed ubuntu 9.10 and my hp laptop has a wireless (this one works just like the normal volume button touch screen if u touch it wireless works or else it doesnot )
now after installing ubuntu it glows always red and never turn blue..
i have windows 7 on other partition it... (0 Replies)
Discussion started by: phoenix_nebula
0 Replies
7. Solaris
while using oracle solaris live upgrade it is mentioned to set few mountpoints like that.. what is the point doing that. (1 Reply)
Discussion started by: chidori
1 Replies
8. Red Hat
I use lspci and dmesg command and find out that i have ipw2000 wireless card on my laptop. I want to install driver for that but i'm not getting proper driver for that.My linux version is el5 and architecture is i386. (0 Replies)
Discussion started by: amitbharad
0 Replies
9. What is on Your Mind?
Did not know where to post this.
Could someone help me with getting my wireless mouse to work?
I can post more specifics at that time.
Thanks. (9 Replies)
Discussion started by: drew77
9 Replies
LEARN ABOUT DEBIAN
essidscan
ESSIDSCAN(8) Commands ESSIDSCAN(8)
NAME
essidscan - scan for ESSID corresponding to available WLAN access points
SYNOPSIS
In /etc/network/interfaces:
mapping <interface> script essidscan
DESCRIPTION
The essidscan utility is used to tell the ifup and ifdown utilities about the current SSID of the WLAN currently being accessed. It can be
used to map the SSID name to an iface stanza.
CONFIGURATION
A sample /etc/network/interfaces may look like this:
mapping hotplug
script /etc/network/essidscan
map SSIDONE wlan-work
map SSIDTWO wlan-work
map HOME
iface wlan-work inet dhcp
wireless-key 1234-5678-9ABC-DEF0-1234-5678-9A
wireless-keymode restricted
iface HOME inet static
address 192.168.2.4
netmask 255.255.255.0
gateway 192.168.2.1
wireless-essid HOME
wireless-key s:somepassword
wireless-keymode open
iface DEFAULT inet dhcp
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
SEE ALSO
interfaces(5) ifscheme(8) ifup(8) ifdown(8)
AUTHORS
Tor Slettnes <tor@slett.net>
ESSIDSCAN(8)