SG_TEST_RWBUF(8)						     SG3_UTILS							  SG_TEST_RWBUF(8)

NAME

       sg_test_rwbuf - Tests the SCSI host adapter by issuing write and read operations on a device's buffer and calculating checksums.

SYNOPSIS

       sg_test_rwbuf [--addrd=AR] [--addwr=AW] [--help] [--quick] --size=SZ [--times=NUM] [--verbose] [--version] DEVICE

       or an older deprecated format sg_test_rwbuf DEVICE SZ [AW] [AR]

DESCRIPTION

       sg_test_rwbuf writes and reads back SZ bytes to the internal buffer of DEVICE (e.g. /dev/sda or /dev/sg0). A pseudo random pattern is writ-
       ten to the data buffer on the device then read back. If the same pattern is found 'Success' is reported. If they do  not  match	(checksums
       unequal)  then this is reported and up to 24 bytes from the first point of mismatch are reported; the first line shows what was written and
       the second line shows what was received. For testing purposes, you can ask it to write AW or read AR additional bytes.

OPTIONS

       Arguments to long options are mandatory for short options as well.

       -r, --addrd=AR
	      Read an additional AR bytes (than indicated by SZ) from the data buffer. Checksum is performed over the first SZ bytes.

       -w, --addwr=AW
	      Write an additional AW bytes (than indicated by SZ) of zeros into the data buffer. Checksum is generated over the first SZ bytes.

       -h, --help
	      Print out a usage message the exit.

       -q, --quick
	      Perform a READ BUFFER descriptor command to find out the available data buffer length and offset, print them out then exit  (without
	      testing with write/read sequences).

       -s, --size=SZ
	      where  SZ is the size of buffer in bytes to be written then read and checked. This number needs to be less than or equal to the size
	      of the device's data buffer which can be seen from the --quick option.  Either this option or the --quick option should be given.

       -t, --times=NUM
	      where NUM is the number of times to repeat the write/read to buffer test. Default value is 1 .

       -v, --verbose
	      increase verbosity of output.

       -V, --version
	      print version number (and data of last change) then exit.

NOTES

       The microcode in a SCSI device is _not_ modified by doing a WRITE BUFFER command with its mode set to "data" (0x2) as done by this utility.
       Therefore this utility is safe in that respect. [Mode values 0x4, 0x5, 0x6 and 0x7 are the dangerous ones :-)]

       WARNING: If you access the device at the same time (e.g. because it's a hard disk with a mounted file system on it) the device's buffer may
       be used by the device itself for other data at the same time, and overwriting it may or may not cause data corruption!  HOWEVER	the  SPC-3
       draft  standard	does state in its WRITE BUFFER command: "This command shall not alter any medium of the logical unit when data mode ... is
       specified". This implies that it _is_ safe to use this utility with devices that have mounted file systems on them.  Following  this  theme
       further, a disk with active mounted file systems may cause the data read back to be different (due to caching activity) to what was written
       and hence a checksum error.

EXIT STATUS

       The exit status of sg_test_rwbuf is 0 when it is successful. Otherwise see the sg3_utils(8) man page.

AUTHORS

       Written by D. Gilbert and K. Garloff

COPYRIGHT

       Copyright (C) 2000-2011 Douglas Gilbert, Kurt Garloff
       This software is distributed under the GPL version 2. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A  PARTICULAR  PUR-
       POSE.

sg3_utils-1.31							   February 2011						  SG_TEST_RWBUF(8)