08-30-2011
9600,8,N,1
if you can, check with a notebook with a serial cisco cable (the baby blue ones) and a terminal software (putty, teraterm, hyperterm, tip, ...) if there is output from the serial server port. if this works you have to search on the TS side or the cables.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
2. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
3. Red Hat
System: Red Hat Enterprise Linux WS release 4 (Nahant Update 6)
Any idea how to Determine if a Serial Port in Linux System is defective?
Issued "cat /proc/tty/driver/serial". see below.
~# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:11... (0 Replies)
Discussion started by: etcpasswd
0 Replies
4. Fedora
Greetings,
A sort of newbie question...
I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies
5. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. HP-UX
Hi Experts,
Need your help in enabling the ftp port in HP-UX box.
Is there any command/config file that needs to be changed?
Also is it possible to open it only for few selected IPs only? (9 Replies)
Discussion started by: sai_2507
9 Replies
8. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
iscc(7) Miscellaneous Information Manual iscc(7)
NAME
iscc - serial communications interface
SYNOPSIS
controller iscc0 at isa0
DESCRIPTION
An onboard Zilog 8530 DUART provides AXPvme-based Single Board Computers with console (CON) and auxiliary (AUX) serial communications
ports. Both serial communications ports can operate at baud rates from B50 to B38400, excluding B134 (see tty(7)).
On AXPvme Single Board Computers configured with a graphics head as the system console, the CON serial communications port (/dev/tty01) is
available for use by application programs as an additional communications port.
In the absence of a graphics head, the CON serial communications port (/dev/console) becomes the system console. When used as the serial
system console, the CON serial communications port always operates at 9600 BPS, 8-bits, and no parity.
Regardless of system console, the AUX serial communications port (/dev/tty00) is always available for use by application programs.
RESTRICTIONS
Data communications equipment attached to the CON serial communications port must be set to 9600 BPS, 8-bits, no parity when configured as
the serial system console. The iscc terminal driver enforces this restriction.
No modem control is supported for either the CON or AUX serial communications ports.
FILES
console terminal local terminal local terminal
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
iscc(7)