08-30-2011
9600,8,N,1
if you can, check with a notebook with a serial cisco cable (the baby blue ones) and a terminal software (putty, teraterm, hyperterm, tip, ...) if there is output from the serial server port. if this works you have to search on the TS side or the cables.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
2. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
3. Red Hat
System: Red Hat Enterprise Linux WS release 4 (Nahant Update 6)
Any idea how to Determine if a Serial Port in Linux System is defective?
Issued "cat /proc/tty/driver/serial". see below.
~# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:11... (0 Replies)
Discussion started by: etcpasswd
0 Replies
4. Fedora
Greetings,
A sort of newbie question...
I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies
5. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. HP-UX
Hi Experts,
Need your help in enabling the ftp port in HP-UX box.
Is there any command/config file that needs to be changed?
Also is it possible to open it only for few selected IPs only? (9 Replies)
Discussion started by: sai_2507
9 Replies
8. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
dc(4) Kernel Interfaces Manual dc(4)
Name
dc - serial line/mouse/keyboard
Syntax
device dc0 at ibus? vector dcintr
Description
The serial line controller provides four ports, with modem control on two of the ports. The DECstation 3100 and DECstation 2100 only pro-
vide partial modem control. The DECstation 5000 provides full modem control. The ports are used as follows:
Port Usage
0 Graphics device keyboard at 4800 BPS
1 Mouse or tablet at 4800 BPS
2 Communications port 1 (w/modem control)/local terminal
3 Communications port 2 (w/modem control)/local terminal
Each communication port from the serial line controller behaves as described in and can be set to run at any of 16 speeds. For the encod-
ing, see
When a graphics device is not being used as the system console, communications port 2 becomes the system console. In this configuration,
the port can only be used at 9600 BPS and no modem control is supported.
The serial line driver operates in interrupt-per-character mode (all pending characters are flushed from the silo on each interrupt).
Restrictions
Speed must be set to 9600 BPS on the console port and 4800 BPS on ports used by graphics devices. The serial line driver enforces this
restriction; that is, changing speeds with the command may not always work on these ports.
Files
console terminal
local terminal
local terminal
See Also
console(4), devio(4), tty(4), ttys(5), MAKEDEV(8)
RISC dc(4)