|
|
Sponsored Content
Operating Systems
Solaris
How to enable Serial port on ILOM, when Network Port is enabled in parallel
Post 302551460 by DukeNuke2 on Tuesday 30th of August 2011 11:56:46 AM
08-30-2011
|
|
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
2. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
3. Red Hat
System: Red Hat Enterprise Linux WS release 4 (Nahant Update 6)
Any idea how to Determine if a Serial Port in Linux System is defective?
Issued "cat /proc/tty/driver/serial". see below.
~# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:11... (0 Replies)
Discussion started by: etcpasswd
0 Replies
4. Fedora
Greetings,
A sort of newbie question...
I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies
5. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. HP-UX
Hi Experts,
Need your help in enabling the ftp port in HP-UX box.
Is there any command/config file that needs to be changed?
Also is it possible to open it only for few selected IPs only? (9 Replies)
Discussion started by: sai_2507
9 Replies
8. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT ULTRIX
mdc
mdc(4) Kernel Interfaces Manual mdc(4) Name mdc - DS5100 serial line driver Syntax device mdc0 at ibus? vector mdcintr device mdc1 at ibus? vector mdcintr device mdc2 at ibus? vector mdcintr Description A DS5100 base system (mdc0) provides four asynchronous ports. An optional asynchronous card (mdc1 and mdc2 ) can be added to supply eight additional ports. The mdc ports are used as follows: Port Usage Connector 0 Console port 6-pin MMJ on CPU board 1 Local terminal 6-pin MMJ on CPU board 2 Full modem control port 25-pin D-Sub on CPU board 3 Local terminal 6-pin MMJ on CPU board An optional asynchronous board provides an additional eight lines: 4 Local terminal 6-pin MMJ 5 Local terminal 6-pin MMJ 6 Full modem control port 25-pin D-Sub 7 Local terminal 6-pin MMJ 8 Local terminal 6-pin MMJ 9 Local terminal 6-pin MMJ 10 Local terminal 6-pin MMJ 11 Local terminal 6-pin MMJ The console baud rate is set to 9600 baud by default. You can change this by setting the baud environment variable from console prompt. Each communication port from the serial line controller behaves as described in the reference page and can be set to run at any of 16 speeds. For the encoding, see You can establish the state of port 2 (port 6) by specifying either modem or nomodem as part of the file entry. Restrictions The speed default is to 9600 baud on the console port. The console device must be set for 8-bit character length with one stop bit and no parity. The driver enforces these restrictions; that is, changing speeds with the command may not always work on console ports. Files Console terminal Full modem control or local terminal See Also console(4), devio(4), tty(4), ttys(5), MAKEDEV(8) RISC mdc(4)