08-30-2011
the serial port on the server is enabled by default. maybe your terminal server settings are wrong or you are using a wrong cable.
This User Gave Thanks to DukeNuke2 For This Post:
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
2. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
3. Red Hat
System: Red Hat Enterprise Linux WS release 4 (Nahant Update 6)
Any idea how to Determine if a Serial Port in Linux System is defective?
Issued "cat /proc/tty/driver/serial". see below.
~# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:11... (0 Replies)
Discussion started by: etcpasswd
0 Replies
4. Fedora
Greetings,
A sort of newbie question...
I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies
5. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. HP-UX
Hi Experts,
Need your help in enabling the ftp port in HP-UX box.
Is there any command/config file that needs to be changed?
Also is it possible to open it only for few selected IPs only? (9 Replies)
Discussion started by: sai_2507
9 Replies
8. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT SUSE
plipconfig
PLIPCONFIG(8) PLIPCONFIG(8)
NAME
plipconfig - fine tune PLIP device parameters
SYNOPSIS
plipconfig interface
plipconfig interface [nibble NN] [trigger NN] [unit NN]
DESCRIPTION
Plipconfig is used to (hopefully) improve PLIP performance by changing the default timing parameters used by the PLIP protocol. Results are
dependent on the parallel port hardware, cable, and the CPU speed of each machine on each end of the PLIP link.
If the single interface argument is given, plipconfig displays the status of the given interface only. Otherwise, it will try to set the
options.
OPTIONS
nibble NN
Sets the nibble wait value in microseconds. Default is 3000.
trigger NN
Sets the trigger wait value in microseconds. Default is 500.
PLIP speed can in some cases be improved by lowering the default values. Values which are too low may cause excess use of CPU, poor inter-
rupt response time resulting in serial ports dropping characters, or in dropping of PLIP packets. Changing the plip MTU can also affect
PLIP speed.
NOTE
If you get no response it is far more likely the irq is wrong and needs setting with ifconfig. The few cases where the default parameters
will be too fast are those using very long cables. Something you should never do as the parallel port is not specified or designed for
driving long cable runs.
SEE ALSO
ifconfig(8)
BUGS
Non.
AUTHOR
John Paul Morrison, <jmorriso@bogomips.ee.ubc.ca>, <ve7jpm@ve7jpm.ampr.org>
17 February 1995 PLIPCONFIG(8)