08-30-2011
the serial port on the server is enabled by default. maybe your terminal server settings are wrong or you are using a wrong cable.
This User Gave Thanks to DukeNuke2 For This Post:
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
2. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
3. Red Hat
System: Red Hat Enterprise Linux WS release 4 (Nahant Update 6)
Any idea how to Determine if a Serial Port in Linux System is defective?
Issued "cat /proc/tty/driver/serial". see below.
~# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:11... (0 Replies)
Discussion started by: etcpasswd
0 Replies
4. Fedora
Greetings,
A sort of newbie question...
I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies
5. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. HP-UX
Hi Experts,
Need your help in enabling the ftp port in HP-UX box.
Is there any command/config file that needs to be changed?
Also is it possible to open it only for few selected IPs only? (9 Replies)
Discussion started by: sai_2507
9 Replies
8. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
SPIF(4) BSD Kernel Interfaces Manual SPIF(4)
NAME
spif -- SBus (spiffy) Serial/Parallel Interface
SYNOPSIS
spif* at sbus? slot ? offset ? (sun4c/sun4m/sun4u)
stty* at spif? (sun4c/sun4m/sun4u)
sbpp* at spif? (sun4c/sun4m/sun4u)
DESCRIPTION
The spif driver provides support for the Sun Serial/Parallel Interface card (Sun part number 501-1931), which is based on the Cirrus Logic
CD180 octal serial controller and the Cirrus Logic PPC2 parallel port controller.
The device minor numbers for this driver are encoded as follows:
+---+---+---+---+---+---+---+---+
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+---+---+---+---+---+---+---+---+
| | | | | | | |
| | | | | +---+---+---> port number
| | | | |
| | | | +---------------> unused
| | | |
| | | +-------------------> dial-out (on tty ports)
| | |
| | +-----------------------> unused
| |
+---+---------------------------> card number
Up to four cards are supported in the system.
Each of the serial ports has an 8 byte FIFO for receive and transmit as well as automatic hardware (RTS/CTS) flow control.
FILES
/dev/ttyS[0123][0-7] Serial ports
/dev/bppS[0-3] Parallel ports
DIAGNOSTICS
spif%d: ccr timeout A timeout occurred while writing to one of the CD180 registers.
stty%d-%d: ring overflow Incoming characters were discarded because the application in control of the device did not read the input fast
enough.
SEE ALSO
intro(4), sbus(4), tty(4)
HISTORY
The spif adapter was first supported in OpenBSD 2.5. The driver was ported to NetBSD 3.0.
AUTHORS
The driver was written by Jason Wright <jason@thought.net>, and is heavily based on the magma(4) driver written by Iain Hibbert.
TODO
The parallel port is not supported yet.
Dial-out (cua) devices are not yet supported.
BSD
February 4, 1999 BSD