08-30-2011
How to enable Serial port on ILOM, when Network Port is enabled in parallel
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected through a terminal server, authentication to the terminal server is successful and conformed port is opened, but cant able to view the console of the server.
So how do I need to make sure to enable the serial port on iLOM.
Thanks
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
2. Solaris
Hi,
I'm using Solaris workstation with 5.4 OS.
I was wondering if there's a way that I could
log the data incoming and outgoing on a certain
serial port.
Thanks in Advance! (1 Reply)
Discussion started by: uryuu
1 Replies
3. Red Hat
System: Red Hat Enterprise Linux WS release 4 (Nahant Update 6)
Any idea how to Determine if a Serial Port in Linux System is defective?
Issued "cat /proc/tty/driver/serial". see below.
~# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:11... (0 Replies)
Discussion started by: etcpasswd
0 Replies
4. Fedora
Greetings,
A sort of newbie question...
I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies
5. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. HP-UX
Hi Experts,
Need your help in enabling the ftp port in HP-UX box.
Is there any command/config file that needs to be changed?
Also is it possible to open it only for few selected IPs only? (9 Replies)
Discussion started by: sai_2507
9 Replies
8. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
dc(7) Miscellaneous Information Manual dc(7)
NAME
dc - serial line/mouse/keyboard
SYNOPSIS
controller dc0 at ibus0 slot 0 vector dcintr
DESCRIPTION
The dc serial line controller provides DECstation 2100, DECstation 3100, DECstation 5000, and DECstation 5100 computer systems with key-
board, mouse, and serial communications interfaces. The serial communications interfaces on the DECstation 2100 and DECstation 3100 provide
partial modem control. The serial communications interfaces on the DECstation 5000 provide full modem control. The device special file
/dev/tty01 on a DECstation 5100 provides full modem control, while the remaining ports provide no modem control at all. All serial commu-
nications interfaces operate at baud rates from B50 to B9600, excluding B200.
The dc ports are used as follows: Usage Graphics device keyboard at 4800 BPS Mouse or tablet at 4800 BPS Communications port 1 (w/modem
control)/local terminal Communications port 2 (w/modem control)/local terminal
On all systems except the DECstation 5100, serial port 2 is used for the system console port in server (that is, non-graphics) configura-
tions. On DECstation 5100s, the serial port labeled 3 on the back of the system is always the system console port. The serial system con-
sole port always operates at 9600 BPS, 8-bits, no parity; modem control is not supported.
RESTRICTIONS
Data communications equipment attached to the console serial port in server configurations must be set to 9600 BPS, 8-bits, no parity. The
scc driver enforces this restriction.
FILES
console terminal local terminal local terminal local terminal (DECstation 5100 only)
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
dc(7)