Sponsored Content
Operating Systems Solaris How to configure the host to dhcp mode Post 302551315 by papertiger on Tuesday 30th of August 2011 04:27:20 AM
Old 08-30-2011
How to configure the host to dhcp mode

I try a static ip assign mode while i installed the Solaris 10(U 8). But i can't access the internet, i try the ifconfig -a command and see my configuration is correct in the interface. So i want to get my ip using dhcp. I search from internet. They give me the suggestions.

ifconfig interface dhcp start ( from this command , i get the wait timeout.)

but the corresponding interface haven't been set successful.

Pls give me a hint or link.

Thank u in advance.
 

10 More Discussions You Might Find Interesting

1. IP Networking

Howto configure AIX DHCP Client ?

I use DHCP on my AIX box at home . I want to connect to my Cable ISP as a DHCP Client . the thing I did was this : smit Communications Applications and Services TCP/IP Use DHCP for TCPIP Configuration and Startup "Select the interface you want to use" en0 "Enter a hostname" OK after... (3 Replies)
Discussion started by: zumbi
3 Replies

2. Linux

How to configure Dhcp in linux?

Please let me know step by step, I am new to this configuration.... (2 Replies)
Discussion started by: dhineshcs
2 Replies

3. Shell Programming and Scripting

Delete Blank Lines Between DHCP Host Blocks

Hi All, I have a dhcpd.conf file that gets static hosts added and removed via a shell script. After sometime, there becomes huge gaps of space ( blank lines ) between each host block. I tried a couple of sed one-liners; but, I can't seem to get the output I'm looking for. Also, I would like... (4 Replies)
Discussion started by: cstovall
4 Replies

4. IP Networking

How to configure DHCP to Static IP

I am pretty new to this. My router was earlier configured to enable DHCP, thus my UNIX box is using the dhcp address, i.e. I have to do a ifconfig dhcp hme0 start. Since I am planning to use my NT as a web server, I needed to use the static IP address. How do I configure the unix box to use the... (5 Replies)
Discussion started by: lee30320
5 Replies

5. Solaris

Failed to configure IPv4 for DHCP afe0

Hi All, i have been accessing ip address through DHCP for my windows..i tried to configure the same for solaris also and got the error " Failed to configure IPv4 for DHCP afe0 " can anyone explain what should i do ...i want to acees internet in solaris am i need to configure for... (0 Replies)
Discussion started by: srikanthg
0 Replies

6. Solaris

custom jumpstart on x86 with DHCP/PXE goes into interactive mode

client boots fine, it gets the ip 192.168.0.10 and the bootfile. Then there is : SunOS 5.10 Version Generic_141445-09 32-bit" ... Configuring devices. Custom JumpStart Reading ZFS config: done Setting up Java. Please wait ... NOTE: Not enough memory for graphical installation. Graphical... (4 Replies)
Discussion started by: TomSu
4 Replies

7. Solaris

Configure network in unix with dynamic ip on my DHCP server?

can anyone tell me how can i configure network in unix with dynamic ip on my DHCP server?? (7 Replies)
Discussion started by: Reham.Donia
7 Replies

8. IP Networking

About Configure the DHCP to assign the Default-Gateway

I have a question. How to write the DHCP to assign the default-gateway to clients. Thank you. (2 Replies)
Discussion started by: thsecmaniac
2 Replies

9. Solaris

DHCP is getting different class of IP than host machine on Solaris 10

i have a laptop with windows 7 installed . this laptop is dhcp enabled and it's details are as follows : IPv4 Address. . . . . . . . . . . : 10.1.5.54 Subnet Mask . . . . . . . . . . . : 255.255.255.192 Default Gateway . . . . . . . . . : 10.1.5.1 i installed solaris 10 on vmware on... (5 Replies)
Discussion started by: rehantayyab82
5 Replies

10. HP-UX

From a C++ application how to find if a hpux host is in standard mode or trusted mode

is there a way for my C++ application to find out which mode the hpux OS is running in? standard mode or trusted mode. (3 Replies)
Discussion started by: einsteinBrain
3 Replies
All times are GMT -4. The time now is 07:24 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy