08-25-2011
v890 cannot boot
I just received a v890. I cannot get it to boot via CDROM nor can I access the SC prompt because I do not know the password. I am attempting to access it via serial cable to a Linux box.
What is the best way to proceed?
10 More Discussions You Might Find Interesting
1. Solaris
hi expert,
sorry i'm new in solaris system, need more advice and help :)
i'm confusing with mirroring disk at my sparc v890 solaris 8, i have 6 harddisk which the structure shown below :
format :
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>
... (4 Replies)
Discussion started by: bucci
4 Replies
2. UNIX for Advanced & Expert Users
Hello,
Need to know all benefits\differences for V890 over V880.
We are really keen to know about this.
Can anybody please take out some time and get us the information.
Regards,
Narinder (4 Replies)
Discussion started by: narinderd
4 Replies
3. Solaris
Question, I have a new V890 preloaded witrh Solaris 10. Due to SW compatibility I need to run Sol 8 on the server. When running boot cdrom from the ok prompt, I get amessages looking for a location on the CDROM to find the startup install SW. The path must be different from what's on Sol 10 install... (4 Replies)
Discussion started by: stocksj
4 Replies
4. Solaris
Hi all,
After the V890 server shutdown unexpectedly, it became unaccessible from RSC. There is one error message about it: rscadm: RSC firmware not responding
Do you have experienced this? Please help! (1 Reply)
Discussion started by: bamboonix
1 Replies
5. Solaris
Hello Experts,
I have a StorEdge 3320 attached to V890, the problem is that I am copying data from v890's internal hdds to 3320's hdds, it is taking a-lot of time, the transfer is very slow.
while I have checked the transfer from V890's internal hdd to another machines it is good. So, its mean... (15 Replies)
Discussion started by: bluetooth
15 Replies
6. Solaris
Hi all!
I've a machine - SunFire V890, it've been failed by OS error for 2 weeks ago, and now, I must reinstall OS (Solaris 10 2009), the progress was successful, but when I reboot, it displayed the error like :
Error -256: Last trap memory ... access aligned
Error -256: Last trap memory... (1 Reply)
Discussion started by: trantuananh24hg
1 Replies
7. Solaris
Dear All,
I need your help. I have server like this
SunOS 5.10 Generic_141444-09 sun4u sparc SUNW,Sun-Fire-V890
with messages like this...
Oct 10 17:07:52 iscsi: NOTICE: unrecognized ioctl 0x403
Oct 10 17:07:52 scsi: WARNING: /pseudo/fcp@0 (fcp0):
Oct 10 17:07:52 Invalid... (4 Replies)
Discussion started by: mbah_jiman
4 Replies
8. Hardware
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
9. Solaris
I am battling to get a V890 up and running. The system appears to have AUTOBOOT=false, so no OS comes up when it's powered on, and I do not have the credentials to get to the RSC management console. Output to ttya serial console ends at "Probing I/O buses", I assume because output is then being... (4 Replies)
Discussion started by: dstmark
4 Replies
10. Solaris
Hi all
I am currently using a T5120 to write and run some simulation code I've been working on which heavily relies on large matrix multiplication procedures. I am posting this to call out for some of you run and share the results of a simple benchmark I've written to compare the matrix... (1 Reply)
Discussion started by: toguro123
1 Replies
VLOCK(1) General Commands Manual VLOCK(1)
NAME
vlock - Virtual Console lock program
SYNOPSIS
vlock
vlock [ -a,--all ] [ -c,--current ] [ -h,--help ] [ -v,--version ]
DESCRIPTION
vlock is a program to lock one or more sessions on the Linux console. This is especially useful for Linux machines which have multiple
users with access to the console. One user may lock his or her session(s) while still allowing other users to use the system on other vir-
tual consoles. If desired, the entire console may be locked and virtual console switching disabled.
By default, only the current VC (virtual console) is locked. With the -a,-all option all VCs are locked. The locked VCs cannot be
unlocked without the invoker's password. And, for the paranoid, vlock makes it a trying experience for those attempting to guess the pass-
word, so unauthorized access to session(s) is highly unlikely.
Please note that it is entirely possible to completely lock yourself out of the console with the -a,--all option if you cannot remember
your password! Unless you are able to kill vlock by logging in remotely via a serial terminal or network, a hard reset is the only method
of ``unlocking'' the display.
vlock works for console sessions primarily. However, there is support for trying to lock non-console sessions as well, but that support
has not been well tested.
OPTIONS
-a,--all
Lock all console sessions and disable VC switching.
-c,--current
Lock the current session (this is the default).
-h,--help
Print a brief help message.
-v,--version
Print the version number of vlock.
AUTHOR
Michael K. Johnson <johnsonm@redhat.com>
Linux User's Manual 16 May 1996 VLOCK(1)