Hi
I am a beginner to sed command, here I have a question about using sed to add a few characters into a token of a string.
For example, I have a file,
sqw:qqq:123124:uiqe
dfd:ccc:12390:dfjis
cde:aaa:21311:dfjsid
and, I want the output to be,
sqw:qqq:123124:uiqe... (4 Replies)
Hi,
I have a file with this format:
name number
-------------- -----------
AAA 11700
BBB 6000
CCC 6000
I want to catch any of these names if number > 200
How to do that?
at a... (4 Replies)
I want to find duplicates in file on 2nd field i wrote this code:
nawk '{a++} END{for i in a {if (a>1) print}}' temp
Could not find whats wrong with this.
Appreciate help (5 Replies)
I want to find the top N entries for a certain field based on the values of another field.
For example if N=3, we want the 3 best values for each entry:
Entry1 ||| 100
Entry1 ||| 95
Entry1 ||| 30
Entry1 ||| 80
Entry1 ||| 50
Entry2 ||| 40
Entry2 ||| 20
Entry2 ||| 10
Entry2 ||| 50... (1 Reply)
I want to sort alphabetically on the first field and sort in descending numerical order on the 2nd field. With a normal "sort -r -n" it does this:
abc ||| 5e-05 ||| bla
abc ||| 3 ||| ble
def ||| 1 ||| abc
def ||| 0.2 ||| def
As you can see it ignores the fact that 5e-05 is actually 0.00005... (1 Reply)
Hi,
I've internally searched through forums for about 2+ hours. Unfortunately, with no luck. Although I've found some cases close to mine below, but didn't help so much.
Actually, I'm in short with time. So I had to post my case. Hoping that you can help.
I have 2 files,
FILE1
... (0 Replies)
Hi,
I've internally searched through forums for about 2+ hours. Unfortunately, with no luck. Although I've found some cases close to mine below, but didn't help so much.
Actually, I'm in short with time. So I had to post my case. Hoping that you can help.
I have 2 files,
FILE1
... (1 Reply)
I have a requirement to replace "\" with "/" in only the 2nd field of the input file which has 2 fields. The field delimiter is "|"
Sample records from input file:
1\23|\tmp\user
mn\wer|\home\temp
Expected output:
1\23|/tmp/user
mn\wer|/home/temp
I used
sed 's/\\/\//g'
... (2 Replies)
Hi,
For example:
I have:
HostA,XYZ
HostB,XYZ
HostC,ABC
I would like the output to be:
HostA,HostB: XYZ
HostC:ABC
How can I achieve this?
So far what I though of is: (1 Reply)
Discussion started by: alvinoo
1 Replies
LEARN ABOUT PLAN9
faith
FAITH(4) BSD Kernel Interfaces Manual FAITH(4)NAME
faith -- IPv6-to-IPv4 TCP relay capturing interface
SYNOPSIS
device faith
DESCRIPTION
The faith interface captures IPv6 TCP traffic, for implementing userland IPv6-to-IPv4 TCP relay like faithd(8).
Each faith interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using
the cloned_interfaces variable in rc.conf(5).
Special action will be taken when IPv6 TCP traffic is seen on a router, and the routing table suggests to route it to the faith interface.
In this case, the packet will be accepted by the router, regardless of the list of IPv6 interface addresses assigned to the router. The
packet will be captured by an IPv6 TCP socket, if it has the IN6P_FAITH flag turned on and matching address/port pairs. As a result, faith
will let you capture IPv6 TCP traffic to some specific destination addresses. Userland programs, such as faithd(8) can use this behavior to
relay IPv6 TCP traffic to IPv4 TCP traffic. The program can accept some specific IPv6 TCP traffic, perform getsockname(2) to get the IPv6
destination address specified by the client, and perform application-specific address mapping to relay IPv6 TCP to IPv4 TCP.
The IN6P_FAITH flag on a IPv6 TCP socket can be set by using setsockopt(2), with level IPPROTO_IPV6 and optname IPv6_FAITH.
To handle error reports by ICMPv6, some ICMPv6 packets routed to an faith interface will be delivered to IPv6 TCP, as well.
To understand how faith can be used, take a look at the source code of faithd(8).
As the faith interface implements potentially dangerous operations, great care must be taken when configuring it. To avoid possible misuse,
the sysctl(8) variable net.inet6.ip6.keepfaith must be set to 1 prior to using the interface. When net.inet6.ip6.keepfaith is 0, no packets
will be captured by the faith interface.
The faith interface is intended to be used on routers, not on hosts.
SEE ALSO inet(4), inet6(4), faithd(8)
Jun-ichiro itojun Hagino and Kazu Yamamoto, An IPv6-to-IPv4 transport relay translator, RFC3142.
HISTORY
The FAITH IPv6-to-IPv4 TCP relay translator first appeared in the WIDE hydrangea IPv6 stack.
BSD April 10, 1999 BSD