I have a modem connect it to ttyS0 , in unix sco i know i can disable and enable the port , how can i do this , is there a command that will allow me to do this.
**** I'm running Redhat 9
*****External Usrobotics 56k
Thanks a lot guys (1 Reply)
How can i disable rlogin or rcopy from being running as a services in my system ? is there a way ? and is it gonna affect other remote services like ssh and telnet ? (3 Replies)
Could anybody tell me how I can disable or enable the backspace key in vi editor.
I would like to feel the essence of the commands of vi editor but as I have the latest version and it is supporting the backspace key.
I do it on promp using the command
stty erase -
This command stops the... (5 Replies)
Hi All,
I am new to cronjob and need some guidance on this.
1) How do i enable a cronjob ?
Can it be done by "crontab mycronfile" or "crontab -e mycronfile"
2) How can i disable the cronjob?
Can deleting of the "mycronfile" disable the cron or do i need to perform "crontab -r mycronfile"... (7 Replies)
Hello,
We recently had a Nessus scan done of our system and the solution to one of the findings was this:
disable the RIP agent and use an EGP routing protocol
I have been unable to find any specific instruction on how to do either. We are running Solaris 8.
Any help would be greatly... (3 Replies)
Hi...
How do I enable SSH and disable telnet..
Also - is there anything special I need to do to ensure that a new user can use ssh and su but not telnet?
Adel (15 Replies)
since i don't have root access, i have been doing:
crontab -l > /tmp/username.crontab
crontab -r
vi /tmp/username.crontab and copy page
crontab -e, and paste
sometimes, /tmp/username.crontab has more than 1 page, so i have to copy twice.
how do i copy all contents from... (2 Replies)
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
LEARN ABOUT CENTOS
clusvcadm
clusvcadm(8) Red Hat Cluster Suite clusvcadm(8)NAME
clusvcadm - Cluster User Service Administration Utility
SYNOPSIS
clusvcadm [-d <service> ] [-e <service> ] [-l] [-u] [-S] [-m <member> ] [-r <service> ] [-R <service> ] [-M <service> ] [-Z <service> ] [-U
<service> ] [-s <service> ] [-v]
DESCRIPTION
The clusvcadm command allows an administrator to enable, disable, relocate, and restart user services in a cluster. In order to perform
cluster service operations, the cluster daemons must be running (and have quorum) on the member system on which the command is invoked.
OPTIONS -d <service>
Stops and disables the user service named service
-e <service>
Enables and starts the user service named service
-l Lock services in preparation for cluster shutdown. This should only be used if the administrator intends to perform a global, clus-
ter wide shutdown. This prevents services from starting (but not stopping, like -Z does). Once the cluster quorum is dissolved,
this state is reset. If a new instance of rgmanager boots while others are locked, the behavior is undefined.
-u Unlock resource group managers. This allows services to start again.
-S Display whether the resource group managers are locked or not. This can be used to verify the correct operation of the -l and -u
options, but is only useful for debugging.
-m <member>
When used in conjunction with either the -e or -r options, this specifies the preferred target member on which to start the service.
-r <service>
Relocates the user service named service to another cluster member.
-R <service>
Restarts the user service named service on the cluster member on which it is currently running.
-M <service>
Use a special "migration" operation to move the user service named service to another cluster member. Currently, this is only use-
ful for virtual machines. Use of migration usually requires special configuration of the local virtual machine manager in order to
work correctly.
-Z <service>
Freezes the service named service on the cluster member on which it is currently running. This will prevent status checks of the
service as well as failover in the event the node fails or rgmanager is stopped.
-U <service>
Unfreezes the user service named service on the cluster member on which it is currently running. This will re-enable status checks.
-s <service>
Stops the service named service until a member transition or until it is enabled again.
-v Display version information and exit.
NOTES
Executing -U (unfreeze) on a service which was frozen in the started state while the service owner is offline results in an undefined (and
possibly dangerous) condition. Manually ensure all resources are clear before doing this.
SEE ALSO clustat(8)
Jan 2005 clusvcadm(8)