08-11-2011
I'd already tried with the --force option....no go I'm afraid.
I should get the replacement disks today so will be physically pulling the drive and crossing my fingers.
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I've recently mirrored the 4 disks in a V440. Disks 0 + 1 have been mirrored with hardware mirroring using the command raidctl -c c1t0d0 c1t2d0, the other 2 disks have been mirrored using Soltisce Disk Suite. I know how to check the progress for the SDS mirroring but how can I find the... (2 Replies)
Discussion started by: Chains
2 Replies
2. Solaris
Hello Gurus!!
Very recently i tried to mount a USB pen drive onto my solaris 10 (X4170 model) server. As i understand, in ideal scenarios it should get mounted automatically, but it did not happen. Neither anything is shown in "iostat -En" output or "rmformat -l" about the pen drive.
I also... (10 Replies)
Discussion started by: EmbedUX
10 Replies
3. UNIX for Advanced & Expert Users
Hello, I have 4 drives (500G each) in a raid 10, I got a power failior and this is the result?
cat /proc/mdstat
Personalities :
md126 : inactive sdb sdc sdd sde
1953536528 blocks super external:-md127/0
md127 : inactive sdd(S) sde(S) sdb(S) sdc(S)
9028 blocks super... (3 Replies)
Discussion started by: rmokros
3 Replies
4. UNIX for Advanced & Expert Users
Hi everyone,
I am not sure if I understand how mdadm --create /dev/md0 --level=container works?
A device called /dev/md0 appears in /proc/mdstat but I am not sure how to use that device?
I have 2 blank drives with 1 500GB partition on each. I would like to setup mirroring, but not in the... (0 Replies)
Discussion started by: hytron
0 Replies
5. Debian
Trying to mount an external 160GB Toshiba drive but....
this is my dmesg tail output:
usb 2-2: new high speed USB device using ehci_hcd and address 3
usb 2-2: New USB device found, idVendor=13fd, idProduct=1618
usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-2:... (4 Replies)
Discussion started by: Ridson
4 Replies
6. Red Hat
had this RHEL 5 installation with /dev/sda1 and /dev/sda2 running..
created two more partitions /dev/sdj1 and /dev/sdj2 , the same sized partition as /dev/sda
trying to use mdadm to create RAID1 ..
I cannot even do it in "rescue" mode, I wonder if it can be done..
it kept... (2 Replies)
Discussion started by: ppchu99
2 Replies
7. UNIX for Dummies Questions & Answers
Hi
I am using SUSE 11 linux
I have couple of "nfs" entries in /etc/fstab which are automatically loaded after system restart.
One of the entry is windows drive mounted using cifs as shown below
//IP-Address/Partition /mnt/x cifs credentials=/creds/.creds,rw,uid=<name> 0 0
I want to... (1 Reply)
Discussion started by: rakeshkumar
1 Replies
8. Filesystems, Disks and Memory
Hello,
i have a system with 6 sata3 seagate st3000dm01 disks running on stable Debian with software raid mdadm. i have md0 for root and md1 for swap and md2 for the files. i now want to add one more disk = sdh4 for md2 but i got this errors:
The new disk is connected to an 4 port sata... (7 Replies)
Discussion started by: Sunghost
7 Replies
9. Solaris
I am connecting a USB mass storage removeable drive to Solaris 10 x86 machine.
The device is detected and i am able to perform standard read and write functions.
But i want to use a code to send IOCTL based SCSI commands to the same device to read and write the data. Which i am unable to do so.... (17 Replies)
Discussion started by: danish2012
17 Replies
10. Solaris
Hi fellow members!
I have a oracle solaris server with two internal disks, that acts as an authentication server only, and for now the server seems to be doing its job, but when typing metastat -c I get some notifications.
I am not familiar with SVM, I wonder if someone can help me on this:... (3 Replies)
Discussion started by: fretagi
3 Replies
iostat(1) General Commands Manual iostat(1)
NAME
iostat - Reports I/O statistics
SYNOPSIS
iostat [drive...] [interval] [count]
OPERANDS
Forces iostat to display specific drives. If drive is not specified (or the specified drive does not exist on the system or cluster,
iostat displays the first two drives (even if more than two disk drives are configured in the system). Causes iostat to report once each
interval seconds. The first report is for all time since the system was last booted, and each subsequent report is for the last interval
only.The value must not be 0. Specifies the number of reports. For example, iostat 1 10 would produce 10 reports at 1-second intervals.
You cannot specify count without interval because the first numeric argument to iostat is assumed to be interval.
DESCRIPTION
The iostat command reports the following information: For terminals (collectively), the number of characters read and written per second.
For each disk, the number of transfers per second and bytes transferred per second (in kilobytes). For the system, the percentage of time
the system has spent in user mode, in user mode running low priority (nice) processes, in system mode, and idling.
To compute this information, iostat counts data transfer completions, the number of words transferred for each disk, and the collective
number of input and output characters for terminals. Also, each sixtieth of a second, iostat examines the state of each disk and makes a
tally if the disk is active.
When you issue an iostat command on a cluster member, it displays statistics only for those disks that are local to the member and that
member's usage of those shared disks that it has mounted. It displays 0 for other disks in the cluster (those it doesn't have mounted),
regardless of whether they are on the shared bus or are local to some other member.
EXAMPLES
The output from this example displays cpu, terminal, and disk statistics for the first two disks on the system providing 5 reports at 1
second intervals:
# iostat 1 5
tty floppy1 dsk9 cpu
tin tout bps tps bps tps us ni sy id
0 3 0 0 0 0 1 0 4 95
4 58 0 0 0 0 1 0 2 97
1 53 0 0 0 0 0 0 2 98
5 59 0 0 0 0 1 0 1 98
6 60 0 0 0 0 1 0 2 97
The second example specifies device names in the command:
# iostat dsk2 dsk3 cdrom2
tty dsk2 cdrom2 dsk3 cpu
tin tout bps tps bps tps bps tps us ni sy id
0 13 11 5 5 2 2427 1213 0 1 1 98
SEE ALSO
Commands:vmstat(1)
iostat(1)