08-03-2011
NTP server to support IPv4 and IPv6 client
Hi
I am looking to have an NTP server that will support both ipv4 and ipv6 clients. Is there anything specific about the configuration that I should be looking at?
9 More Discussions You Might Find Interesting
1. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
2. IP Networking
Hello,
i have a problem with a dns server. It is running bind 9.4.1 (compiled with "-enable-ipv6") on an AIX 5.3 system. The server starts without any errors or warnings. I am also able to lookup names for IPv4 adresses. But with IPv6 i have a strange problem.
When i execute the following dig... (3 Replies)
Discussion started by: skanatiker
3 Replies
3. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
4. AIX
hello
i'm working on AIX 5300-05-03 P520 hacmp 5.4
when connection to the internet is going down , firewall down, my application work verey verey slowly!!! and on the sliffer output i'm got trys of my serevr to do convert from ipv4 ipv6 ( 0.0.2.0 and AAAAAAAA).
some one have an idea why... (1 Reply)
Discussion started by: ariec
1 Replies
5. Linux
I need to configure an NTP daemon on a "bridge-PC" connected on 2 LANs. It is expected to read the correct time on a time server on the first LAN and behave as a server for the second LAN.
Can I do both the things with ntpd?
In other words, is ntpd able to work as client and server at the same... (3 Replies)
Discussion started by: bigjim33
3 Replies
6. IP Networking
Hi,
I have two Cent OS Linux systems and one Ubuntu OS system contains two Ethernet Cards.
I need to create two networks by using Ubuntu sys as router. One network need to configure in IPv4 addresses and another network should configure in IPv6 addresses. Please help me how to configure two... (0 Replies)
Discussion started by: hanuma614
0 Replies
7. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
8. Solaris
Hi,
I am looking for a solution to configure ntp between ipv4 ( ntp server ) to ipv6 ( client) .
I had google, but lot many sites suggest to have dual stock or tunnaling.
my issue is I have client has only ipv6 address ans server has ipv4 address. is it possible to sync time,... (4 Replies)
Discussion started by: naveen.surisett
4 Replies
9. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
LEARN ABOUT DEBIAN
miredo-server.conf
MIREDO-SERVER.CONF(5) System Manager's Manual MIREDO-SERVER.CONF(5)
NAME
miredo-server.conf - configuration for miredo-server
SYNOPSIS
miredo-server.conf
DESCRIPTON
miredo-server.conf is the configuration file for miredo-server. Each configuration directive consists of one directive name, possibly
followed by one or several spaces and a value for the directive. White spaces, empty lines and lines starting with '#' are ignored.
Directives are case-insensitive. A comprehensive list of the supported directives follows:
SERVER OPTIONS
ServerBindAddress server_ip
Specifies the primary IPv4 address of the Teredo server. miredo-server will bind to UDP/IPv4 port 3544 on this address and waits
for packets from Teredo clients. It will advertise the Teredo prefix which is defined with the Prefix directive.
A Teredo server needs two subsequent IPv4 addresses. It will wait for UDP IPv4 packets on port 3544 on both addresses. server_ip
specifies the lowest of both IPv4 addresses, which is known as the primary IPv4 server address. The secondary IPv4 address should be
server_ip + 1 and must also be assigned to the server.
ServerBindAddress2 server_ip2
It is possible to specify a secondary IPv4 server address manually. However, Miredo clients will need manual configuration (with
the ServerAddress2 directive in miredo.conf). Other Teredo clients are believed not to support such setup.
Prefix teredo_prefix
This directive specifies the Teredo prefix which the Teredo relay and/or server will advertise. teredo_prefix must be a valid IPv6
prefix.
The default value is 2001:0000::. A 32-bits prefix is required to use this option. Since you do not have such big an IPv6 prefix
YOU WILL NOT USE THIS OPTION. Moreover, certain third party Teredo client implementations require the default prefix.
InterfaceMTU mtu
This directive overrides the value of the MTU that is advertised to Teredo clients. The default value is 1280 bytes and should not
be changed if the default Teredo prefix is used.
YOU MUST NOT USE THIS OPTION with the default prefix. This would break interoperability with most Teredo relays.
SyslogFacility facility
Specify which syslog's facility is to be used by miredo-server for logging. Possible values are: daemon (the default), local0, ...
local7, kern and user (see syslog(2)).
SEE ALSO
miredo-server(8)
AUTHOR
Remi Denis-Courmont <remi at remlab dot net>
http://www.remlab.net/miredo/
miredo February 2008 MIREDO-SERVER.CONF(5)