07-28-2011
So before this thread dies completely:
Apparently I need to create a root account for the xscf, with which I can run commands like ls, rm and so on, so I can delete the old firmware and free up space. Trouble is, I'm not sure how to do so.
Has anyone done this before?
10 More Discussions You Might Find Interesting
1. Solaris
is there a way to force an error on an xscf much the same way you can with logger on solaris 10? i would like to test and make sure setarchiving is appropriately configured. however, i do not want to just pull a power source as the system is in production. anyway have any insight? showarchiving... (0 Replies)
Discussion started by: pupp
0 Replies
2. Solaris
While entering to service mode on XSCF i getting following error
XSCF> service
Account is not enabled for service mode.
What could be the reason for this ? (5 Replies)
Discussion started by: fugitive
5 Replies
3. Solaris
Hi, I was working on the M3000 and I did a init 0, powered off the system during the weekend. When I tried to poweron today, the XSCF linux boot image keeps on rebooting and does not go to the login for XSCF access. The "Check" LED is on amber. Tried diagnosing but cant get the system up. Any help... (1 Reply)
Discussion started by: incredible
1 Replies
4. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
5. Emergency UNIX and Linux Support
we have a SUN M3000 server.
setup as only 1 domain.
disk c0t0d0 and c0t1d0 and setup as SVM mirrors.
a few days ago disk T1 failed.
new we have replaced the disk, but can's see the disk in format.
have done cfgadm and devfsadm.
still can't access the new disk in format.
the output... (6 Replies)
Discussion started by: robsonde
6 Replies
6. Emergency UNIX and Linux Support
Hi All,
I have SPARC T4-4 connected with XSCF console. By mistake console user name is set to "root" instead of "sunadmin" (This is what we keep as standard). How can I change it ? Please help me
-> show /SP/users/root
/SP/users/root
Targets:
ssh
Properties:
role... (1 Reply)
Discussion started by: solaris_1977
1 Replies
7. Solaris
Hi
We have an M3000 single physical processor and 8gb of memory running Solaris 10. This system runs two Oracle Databases one on Oracle 9i and One on Oracle 10g.
As soon as the Oracle 10g database starts we see an immediate drop in system performance, for example opening an ssh session can... (6 Replies)
Discussion started by: gregsih
6 Replies
8. Solaris
Hi all,
I understand SP is a separate processor use for management purposes.
I understand XSCF is the management facility (similar to IDRAC, ILOM etc).
I understand that we can create multiple domains in a SPARC machine (something like VM) and we can install OS in it.
I am able to use... (4 Replies)
Discussion started by: javanoob
4 Replies
9. Solaris
Hi All,
I have an Oracle M4000 server with Solaris 10 OS. I have access to Solaris root prompt.
But I don't know the XSCF IP of this server.
Is there any way to display XSCF IP from Solaris OS? (2 Replies)
Discussion started by: byrusber
2 Replies
10. IP Networking
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT DEBIAN
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)
NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS
-raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO
ppm(5)
AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)