Dear all,
Please advise what approach can remove all line break from a text file?
e.g.
Source file:
A
B
C
Target file:
A, B, C
Thanks,
Rock (5 Replies)
*Note, I thought I was in Shell Programming and Scripting Q&A and posted in a wrong forum. To avoid confusion and to inform people that I'm not trying to "spam" the forums, I'm adding this note up top*
Hi Everyone thanks in advance for any input you can provide on the following question! I'm... (2 Replies)
hi All,
Have a doubt in ksh..Am not familiar with arrays but i have tried out a script..
plzzzzz correct me with the script
My i/p File is:
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS =
(PROTOCOL = TCP)
(Host = 192.168.2.2)
(Port = 1525)
)
)
(CONNECT_DATA = (SID = TESTDB1)
)
)
... (7 Replies)
Hello All,
I am new to unix scripting, I have an urgent issue
Is it possible to do a group by on the last column and then a page break on the text file.
For example I have a text file, below is the example data
STRT 2154081~VA ~23606 ~TM14~8506~1485
STRT 2130893~VA ~23602 ~TM15~8602~1586... (4 Replies)
I've been trying this, and can't get it right. I want to put a line break before a word, but only if it's *not* the last word in the line. So if the break work was "fish," then...
We want to fish tomorrow
...would become...
We want to
fish tomorrow
...but this line would remain... (3 Replies)
...when the lines use both a colon and commas to separate the parts you want read as information.
The first version of this script used cut and other non-Bash-builtins, frequently, which made it nice and zippy with little more than average processor load in GNOME Terminal but, predictably, slow... (2 Replies)
I cannot seem to get this to work..
I have a file which has about 100 lines, and there is no end of line (line break \n) at the end of each line, and this is causing problem when i paste them into an application.
the file looks like this
this is a test
that is a test
balblblablblhblbha... (1 Reply)
So I'm in a Unix class and our assignment was to go into VI and write a script to make this file tree. At the end of it, I'd like it to echo "This is the file tree you've created" then a line break, then . But I'm not sure as to who to do it. Is there a way for when I run it (./filesystem), the... (4 Replies)
I'm trying to make a script that says
echo This is the date:
I did this
echo This is the date:
date
and it worked. But I need them both on the same line. And putting date on the echo line doesn't work. Is there a way to do so? (1 Reply)
Hello everyone!
I'm trying to make the below file1 look like file2, can anyone help?
Basically I just hit backspace on every line that starts with a number.
Thanks!
file1:
THIS#IS-IT1
4
THIS#IS-IT2
3
THIS#IS-IT3
2
THIS#IS-IT4
1
Result > file2: (4 Replies)
Discussion started by: demmel
4 Replies
LEARN ABOUT PLAN9
pccard
PCCARD(4) BSD Kernel Interfaces Manual PCCARD(4)NAME
pccard -- PC Card bus driver
SYNOPSIS
device pccard
DESCRIPTION
The pccard driver implements the PC Card bus. The pccard driver supports all PC Card bridges in the system.
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.pccard.debug Non-zero values cause more verbose information to be printed when a 16-bit PC Card is inserted or removed.
hw.pccard.cis_debug Non-zero value causes the CIS parsing of the 16-bit PC Card to be much more verbose and include a complete CIS dump.
FILES
/dev/pccard0.cis This exclusive-use device will report all the CIS chains present in a PC Card, if a 16-bit PC Card is inserted in the slot.
Only one user at a time may access the CIS. The CIS is presented as the relevant byte stream from the PC Card. For CIS
tuples in Attribute Memory (the default), only the even locations are presented (the ODD locations are undefined per the
standard). For CIS tuples in Common Memory, every byte is presented to the user. Decoding of the CIS tuples is done via a
userland program. All tuples are presented to the user.
SEE ALSO cardbus(4), pccbb(4)
PC Card Standard, Release 8.
BSD July 9, 2002 BSD