hi, i want to examine two file and write some codes to a third file. note that seperators are TAB, not space.
first file:
192.168.1.1 3
192.168.1.2 2
192.168.3.2 2
192.168.7.3 1
...
second file:
192.168.1.1 1 10.15.1.1 3 30 10.15.2.1 2 40
192.168.1.1 2 10.23.4.5... (3 Replies)
Hi All,
From the title you may know that this question has been asked several times and I have done lot of Googling on this.
I have a Wikipedia dump file in XML format. All the contents are in one XML file i.e. all different topics have been put in one XML file. Now I need to separate them and... (1 Reply)
I need
1. to find all the files from a Folder "folder_name" and from its 4 or 5 sub folders which contain a certain pattern "pattern1".
2. from these files copy and merge all the text between "pattern1" and another different pattern "pattern2" to "mergefile".
3. Get rid of every html tag.
4.... (3 Replies)
Hi,
I want to concatenate the texts in the file but there are different scenario's.
Ist Scenario.
The contents of file has id`language,sequence number,text,language
Here id`language is a key pair to identify the correct language.
Sequnce number is the order the text being inserted.
Text... (3 Replies)
Hello, I have hundreds of text files to be tested.They are generated by many commands. I should check whether a word in specific position is right, or whether a word in file A is equal to a word in file B. All the file are not the same. I decide to use shell to test every files, so I had to write... (7 Replies)
Hi,
I have a file with texts shown below,
<2013 abc
<2013 start
request pdu
dot1q
end pdu
response pdu
dot1q
end pdu
am searching for the text "dot1q" , when it matches in the file , i need the contents between "<2013 start" and "end pdu". Can some one help on this ?
... (5 Replies)
Discussion started by: giri_luck
5 Replies
7. Post Here to Contact Site Administrators and Moderators
Can you add hover texts (alt-texts) to icons? It is not always obvious what each of them mean just by looking at them. Sometimes it is clear from the url it points to, but for accessibility reasons alone it would be good to have alt-texts as a standard. (1 Reply)
is there any way to align my text so every column begins on the same line as the previous line?
here's my command:
printf "THEN ( ${SEARCHPATTB} = Hour = ${CALTOTB} ) %8s => %8s NOW ( ${SEARCHPATT} = Hour = ${CALTOT} ) %7s => %7s Reduced By: %7s -${RESULT}"\\n
output i'm currently getting... (2 Replies)
Discussion started by: SkySmart
2 Replies
LEARN ABOUT NETBSD
comm
COMM(1) BSD General Commands Manual COMM(1)NAME
comm -- select or reject lines common to two files
SYNOPSIS
comm [-123f] file1 file2
DESCRIPTION
The comm utility reads file1 and file2, which should be sorted lexically, and produces three text columns as output: lines only in file1;
lines only in file2; and lines in both files.
The filename ``-'' means the standard input.
The following options are available:
-1 Suppress printing of column 1.
-2 Suppress printing of column 2.
-3 Suppress printing of column 3.
-f Fold case in line comparisons.
Each column will have a number of tab characters prepended to it equal to the number of lower numbered columns that are being printed. For
example, if column number two is being suppressed, lines printed in column number one will not have any tabs preceding them, and lines
printed in column number three will have one.
comm assumes that the files are lexically sorted; all characters participate in line comparisons.
EXIT STATUS
comm exits 0 on success, >0 if an error occurred.
SEE ALSO cmp(1), diff(1), sort(1), uniq(1)STANDARDS
The comm utility conforms to IEEE Std 1003.2-1992 (``POSIX.2'').
BSD June 6, 1993 BSD