07-20-2011
Thanks for the info jlliagre.
I will look into doing it your way. I can't use snoop at work but the other stuff might be really useful.
Last edited by bitlord; 07-21-2011 at 09:22 AM..
Reason: error
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
4. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
10. Solaris
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT DEBIAN
ttysnoops
TTYSNOOP(8) BSD System Manager's Manual TTYSNOOP(8)
NAME
ttysnoop -- snoop on a user's tty
SYNOPSIS
ttysnoop [pty]
ttysnoops
DESCRIPTION
The ttysnoop / ttysnoops client-server combo can be used to snoop (watch) on a user's login tty. The server (ttysnoops) is usually started
by getty(8) or telnetd(8) and reads the file /etc/snooptab to find out which tty's should be cloned and which programs to run on them (usu-
ally /bin/login). A tty may be snooped through a pre-determined (ie. fixed) device, or through a dynamically allocated pseudo-tty (pty).
This is also specified in the /etc/snooptab file. To connect to the pty, the client ttysnoop should be used. The available pseudo terminals
pty are present as sockets in the directory /var/spool/ttysnoop/.
Format of /etc/snooptab
The /etc/snooptab file may contain comment lines (starting with a '#'), empty lines, or entries for tty's that should be snooped upon. The
format of such an entry is as follows:
tty snoop-device type program
where tty is the leaf-name of the tty that should be snooped upon (eg. ttyS2, not /dev/ttyS2) OR the wildcard '*', which matches ANY tty.
snoop-device is the device through which tty should be snooped (eg. /dev/tty8) OR the literal constant "socket". The latter is used to tell
ttysnoops that the snoop-device will be a dynamically allocated pty. type specifies the type of program that should be run, currently recog-
nized types are "init", "user" and "login" although the former two aren't really needed. Finally, program is the full pathname to the program
to run when ttysnoops has cloned tty onto snoop-device.
EXAMPLE
The following example /etc/snooptab file should illustrate the typical use of ttysnoop / ttysnoops:
#
# example /etc/snooptab
#
ttyS0 /dev/tty7 login /bin/login
ttyS1 /dev/tty8 login /bin/login
#
# the wildcard tty should always be the last one in the file
#
* socket login /bin/login
#
# example end
#
With the above example, whenever a user logs in on /dev/ttyS0 or /dev/ttyS1, either tty will be snooped through /dev/tty7 or /dev/tty8
respectively. Any other tty's will be snooped through a pty that will be allocated at the time of login. The system-administrator can then
run ttysnoop pty to snoop through the pty. Note that it is up to the system-administrator to setup getty and/or telnetd so that they execute
ttysnoops instead of /bin/login.
SEE ALSO
getty(8), telnetd(8)
FILES
/etc/snooptab
BUGS
The program is unable to do any terminal control-code translations for the original tty and the snoop-device. I doubt it will ever do this.
AUTHOR
Carl Declerck, carl@miskatonic.inbe.net
BSD
August 8 1994 BSD