07-20-2011
Thanks for the info jlliagre.
I will look into doing it your way. I can't use snoop at work but the other stuff might be really useful.
Last edited by bitlord; 07-21-2011 at 09:22 AM..
Reason: error
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
4. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
10. Solaris
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT OPENSOLARIS
network-admin
network-admin(1) User Commands network-admin(1)
NAME
network-admin - Basic administration of network interfaces.
SYNOPSIS
network-admin [--configure=INTERFACE] [--configure-type=TYPE] [gnome-std-options]
DESCRIPTION
network-admin enumerates the interfaces available to the user and provides a mechanism for configuring these interfaces as static-IP or
DHCP. It's also possible to select which interfaces should be enabled on boot.
network-admin also allows you configure the systems hostname, DNS options and hosts using the user interface.
OPTIONS
The following options are supported:
-c, --configure=INTERFACE Configure a specific network interface (e.g. ath0 or bge0).
-t, --configure-type=TYPE Configure the first network interface of a specific type (e.g. ethernet or wireless).
gnome-std-options Standard options available for use with most GNOME applications. See gnome-std-options(5) for more informa-
tion.
EXAMPLES
Example 1: Running the main application.
example% network-admin
Example 2: Configuring the ath0 network interface.
example% network-admin --configure=ath0
Example 3: Configuring the first ethernet interface.
example% network-admin --configure-type=ethernet
EXIT STATUS
The following exit values are returned:
0 Application exited successfully
>0 Application exited with failure
FILES
The following files are used by this application:
/usr/bin/network-admin Executable for network interface configuration.
/etc/inet/gnome-system-tools Storage location for network configuration files when not active on boot.
/var/spool/setup-tool-backends/backup/network
Backup directory for files that are modified.
/var/spool/setup-tool-backends/data/network
Where "Location" profiles are stored.
/var/run/setup-tool-backends/debug/network
Debug logs can be found under here.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-system-tools |
+-----------------------------+-----------------------------+
|Interface stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
Latest version of the GNOME Desktop User Guide for your platform.
users-admin(1), shares-admin(1), services-admin(1), time-admin(1), gnome-std-options(5), ifconfig(1M), hosts(4), nsswitch.conf(4),
resolv.conf(4), attributes(5)
NOTES
This tool can only be used to manage physical network devices as returned by the "dladm show-dev" command, it does not support configura-
tion of more complex configurations.
There is currently no support for enterprise name services such as YP/NIS, NIS+ or LDAP. There is also no support for anything but the
global zone.
Written by Darren Kenny, Sun Microsystems Inc., 2006.
SunOS 5.11 6 Nov 2006 network-admin(1)