configure zones to have different network interface and network Post: 302540117

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Advanced & Expert Users

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

3. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur

4. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware.

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

6. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

7. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

8. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

10. Solaris

Network / global zones (Solaris 10 / 8) config recommendations

I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network. My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network. I am using the current version of Solaris 10 in...

LEARN ABOUT DEBIAN

expchk

EXPCHK(1p)						User Contributed Perl Documentation						EXPCHK(1p)

NAME

       expchk - Check a keyrec file for expired zones

SYNOPSIS

	 expchk -all -expired -valid -warn numdays -zone zonename -count -help keyrec_files

DESCRIPTION

       expchk checks a set of keyrec files to determine if the zone keyrecs are valid or expired.  The type of zones displayed depends on the
       options chosen; if no options are given the expired zones will be listed.

OPTIONS

       -all
	   Display expiration information on all zones, expired or valid, in the specified keyrec files.

       -expired
	   Display expiration information on the expired zones in the specified keyrec files.  This is the default action.

       -valid
	   Display expiration information on the valid zones in the specified keyrec files.

       -warn numdays
	   A warning will be given for each valid zone that will expire in numdays days.  This option has no effect on expired zones.

       -zone zonename
	   Display expiration information on the zone specified in zonename.

       -count
	   Only the count of matching zones (valid or expired) will be given.  If both types of zones are selected, then the count will be the
	   number of zones in the specified keyrec files.

       -help
	   Display a usage message.

       -Version
	   Displays the version information for expchk and the DNSSEC-Tools package.

COPYRIGHT

       Copyright 2004-2012 SPARTA, Inc.  All rights reserved.  See the COPYING file included with the DNSSEC-Tools package for details.

AUTHOR

       Wayne Morrison, tewok@tislabs.com

SEE ALSO

       zonesigner(8)

       Net::DNS::SEC::Tools::keyrec.pm(3)

perl v5.14.2							    2012-06-21								EXPCHK(1p)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. UNIX for Advanced & Expert Users

network interface problem

Discussion started by: sc2005