Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT OPENSOLARIS
zcons
zcons(7D) Devices zcons(7D)NAME
zcons - Zone console device driver
DESCRIPTION
The zcons character driver exports the console for system zones. The driver is comprised of two "sides:" a master side with which applica-
tions in the global zone communicate, and a slave side, which receives I/O from the master side. The slave side is available in the global
zones.
Applications must not depend on the location of /dev or /devices entries exported by zcons. Inside a zone, the zcons slave side is fronted
by /dev/console and other console-related symbolic links, which are used by applications that expect to write to the system console.
The zcons driver is Sun Private, and may change in future releases.
FILES
/dev/zcons/<zonename>/masterconsole
Global zone master side console for zone <zonename>.
/dev/zcons/<zonename>/slaveconsole
Global zone slave side console for zone <zonename>.
/dev/zconsole
Non-global zone console (slave side).
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
| Interface Stability |Sun Private |
+-----------------------------+-----------------------------+
SEE ALSO zoneadm(1M), zonecfg(1M), attributes(5), zones(5)SunOS 5.11 24 Aug 2003 zcons(7D)