Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT OPENSOLARIS
lx
lx(5) Standards, Environments, and Macros lx(5)NAME
lx - Linux branded zone
DESCRIPTION
The lx brand uses the branded zones framework described in brands(5) to enable Linux binary applications to run unmodified on a machine
with a Solaris Operating System kernel.
The lx brand includes the tools necessary to install a CentOS 3.x or Red Hat Enterprise Linux 3.x distribution inside a non-global zone.
The brand supports the execution of 32-bit Linux applications on x86/x64 machines running the Solaris system in either 32-bit or 64-bit
mode.
Supported Linux Distributions
The lx brand emulates the system call interfaces provided by the Linux 2.4.21 kernel, as modified by Red Hat in the RHEL 3.x distributions.
This kernel provides the system call interfaces consumed by the glibc version 2.3.2 released by Red Hat.
In addition, the lx brand partially emulates the Linux /dev and /proc interfaces.
Configuration and Administration
The lx brand supports the whole root non-global zone model. All of the required linux packages are installed into the private file systems
of the zone.
The zonecfg(1M) utility is used to configure an lx branded zone. Once a branded zone has been installed, that zone's brand cannot be
changed or removed. The zoneadm(1M) utility is used to report the zone's brand type and administer the zone. The zlogin(1) utility is used
to log in to the zone.
Application Support
The lx zone only supports user-level Linux applications. You cannot use Linux device drivers, Linux kernel modules, or Linux file systems
from inside an lx zone.
You cannot add any non-standard Solaris devices to a Linux zone. Any attempt to do so will result in a zone that zonecfg(1M) will refuse to
verify.
You cannot run Solaris applications inside an lx zone. Solaris debugging tools such as DTrace (see dtrace(1M)) and mdb (see mdb(1)) can be
applied to Linux processes executing inside the zone, but the tools themselves must be running in the global zone. Any core files generated
are produced in the Solaris format, and such files can only be debugged with Solaris tools.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWlxr, SUNWlxu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO mdb(1), zlogin(1), zonename(1), dtrace(1M), zoneadm(1M), zonecfg(1M), brands(5), zones(5), lx_systrace(7D)SunOS 5.11 19 Sep 2006 lx(5)