Dear tamitot
when I put the following command # /usr/X11/bin/scanpci, appear
...........
...........
pci bus 0x0000 cardnum 0x04 function 0x00: vendor 0x139 device 0x0900
Silicom Integrated System [SiS] SiS900 PCI Fast Ethernet
...........
...........
After that I put this command prtconf
..........
..........
pci1039,900 (driver not attached)
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
LEARN ABOUT XFREE86
pcitweak
PCITWEAK(1) General Commands Manual PCITWEAK(1)NAME
pcitweak - read/write PCI config space
SYNOPSIS
pcitweak -l
pcitweak -r PCI-ID [-b|-h] offset
pcitweak -w PCI-ID [-b|-h] offset value
DESCRIPTION
Pcitweak is a utility that can be used to examine or change registers in the PCI configuration space. On most platforms pcitweak can only
be run by the root user.
OPTIONS -l Probe the PCI buses and print a line for each detected device. Each line contains the bus location (bus:device:function), chip
vendor/device, card (subsystem) vendor/card, revision, class and header type. All values printed are in hexadecimal.
-r PCI-ID
Read the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in the form
bus:device:function, with each value in hexadecimal. By default, a 32-bit register is read.
-w PCI-ID
Write value to the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in
the form bus:device:function, with each value in hexadecimal. By default, a 32-bit register is written.
-b Read or write an 8-bit value (byte).
-h Read or write a 16-bit value (halfword).
SEE ALSO scanpci(1)AUTHORS
David Dawes (dawes@xfree86.org).
XFree86 Version 4.7.0 PCITWEAK(1)