Dear tamitot
when I put the following command # /usr/X11/bin/scanpci, appear
...........
...........
pci bus 0x0000 cardnum 0x04 function 0x00: vendor 0x139 device 0x0900
Silicom Integrated System [SiS] SiS900 PCI Fast Ethernet
...........
...........
After that I put this command prtconf
..........
..........
pci1039,900 (driver not attached)
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
LEARN ABOUT FREEBSD
if_my
MY(4) BSD Kernel Interfaces Manual MY(4)NAME
my -- Myson Technology Ethernet PCI driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device my
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_my_load="YES"
DESCRIPTION
The my driver provides support for various NICs based on the Myson chipset. The Myson chipset is a variant of the DEC Tulip NIC chipset.
The driver will work with almost any MII-compliant PHY, thus failure to positively identify the chip is not a fatal error.
HARDWARE
The my driver provides support for various NICs based on the Myson chipset. Supported models include:
o Myson MTD800 PCI Fast Ethernet chip
o Myson MTD803 PCI Fast Ethernet chip
o Myson MTD89X PCI Gigabit Ethernet chip
SEE ALSO altq(4), de(4), netintro(4), pci(4), ifconfig(8)HISTORY
The my driver first appeared in FreeBSD 4.6.
AUTHORS
The my driver was written by Myson Technology Inc.
This manual page was written by Hiten M. Pandya <hmp@FreeBSD.org>.
BUGS
The my driver does not support Power Management Events (PME).
BSD March 11, 2007 BSD