07-13-2011
Your interface is not recognized by Solaris , it needs a driver. Can you post what type , what manufacturer and what model is this interface this might help in solving your problem
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
4. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
5. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
6. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
7. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
8. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
9. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
10. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
LEARN ABOUT REDHAT
powercom
POWERCOM(8) Network UPS Tools (NUT) POWERCOM(8)
NAME
powercom - UPS driver for Powercom/Trust/Advice UPS equipment
NOTE
This man page only documents the hardware-specific features of the newapc driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
This driver supports many similar kinds of UPS hardware. The most common ones are the Trust 425/625, Powercom, and Advice Partner/King
PR750. Others using the same protocol may also work.
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5):
linevoltage=value
Specify the line voltage (which can't be autodetected) - 110-120 or 240, default is 230.
manufacturer=value
Specify the manufacturer name, which also can't be autodetected.
modelname=value
Specify the model name, which also can't be autodetected.
serialnumber=value
Like modelname above, but for the serial number.
subtype=value
Sub type of UPS - like KP625AP, Trust or Egys. Default is Trust.
AUTHOR
Peter Bieringer <pb@bieringer.de>
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/
NUT mailing list archives and information: http://lists.exploits.org/
Wed Oct 16 2002 POWERCOM(8)