Sponsored Content
Full Discussion: M4000 fault
Operating Systems Solaris M4000 fault Post 302535619 by callmebob on Friday 1st of July 2011 09:52:17 AM
Old 07-01-2011
Sorted, rogue scsi cable causing, strange but once they were both unplugged it booted?????????
 

10 More Discussions You Might Find Interesting

1. Solaris

M4000 graphics card

Hi Guys, Anyone know any commands to verify the graphics card is installed correctly on an M4000? show-displays just comes back and echoes nothing. Also there is on input-device or output-device variable when you run printenv. This in itself is worrying. Any advice would be... (4 Replies)
Discussion started by: callmebob
4 Replies

2. UNIX for Dummies Questions & Answers

Help with restarting SUN m4000 server

I'm trying to power on our SUN m4000 server after a recent shutdown. When I try to connect to the xscf console I'm getting prompted for a password. The system is not asking for a login just a password. Below is the output from the xscf console. Anyone know how I can safely get back to the... (0 Replies)
Discussion started by: orahi001
0 Replies

3. Solaris

fmadm on an M4000

Hi people, Hoping someone has maybe done this before? I'm trying to run fmadm from the xcsf prompt on an M4000 and it won't run, complaining about insufficient privileges, even though the user has supposedly been setup with fieldeng privileges. Anyone got any ideas? Cheers Rgrds... (10 Replies)
Discussion started by: callmebob
10 Replies

4. Solaris

Single maintence mode cannot run any command on M4000

Hii All I was building two M4000 servers and one was successfully installed. Other one /usr has been unmounted. my putty session got disconnected and i connected to console where it asked for root single maintence # # init 0 not foung # df -h not found # xscf>poweroff -a xscf>... (8 Replies)
Discussion started by: seems
8 Replies

5. Solaris

M4000 Server Issue

Dear Team, This time i am facing some problems in Sun SPARC M4000 server. I have a doubt, when we are upgrading the firmware if XSCF , the OBP is also upgraded. What about server OBP, Is that upgardation need to be done separately ? what about DVD-ROM, HARD DISK firmware.... (3 Replies)
Discussion started by: sudhansu
3 Replies

6. Solaris

M4000 Memory Fault

Hi Guys and Gals, Does anyone know how to track down a faulty DIMM on the memory board of an M4000? showhardconf tells me which board it is, but was wondering if there was a way to track it down to a DIMM? Thanks in advance Martin (5 Replies)
Discussion started by: callmebob
5 Replies

7. Programming

Using gdb, ignore beginning segmentation fault until reproduce environment segmentation fault

I use a binary name (ie polo) it gets some parameter , so for debugging normally i do this : i wrote script for watchdog my app (polo) and check every second if it's not running then start it , the problem is , if my app , remain in state of segmentation fault for a while (ie 15 ... (6 Replies)
Discussion started by: pooyair
6 Replies

8. Solaris

M4000 Mode Switch

Hello, I'm set to go out to our M4000 to reset the XSCF password, since the person who set it up doesn't remember what password they setup. I have all the steps, but the only question I can't find an answer to is around the mode switch. Right now, based on prtdiag, the mode switch is in... (2 Replies)
Discussion started by: QuickNull
2 Replies

9. Solaris

CPU/processor/cores in M4000

Hi Gurus Can someone help me in explaining the below outputs . psrinfo -p 4 /usr/sbin/psrinfo -pv The physical processor has 4 virtual processors (0-3) SPARC64-VI (portid 1024 impl 0x6 ver 0x93 clock 2150 MHz) The physical processor has 4 virtual processors (8-11) SPARC64-VI... (3 Replies)
Discussion started by: ningy
3 Replies

10. Solaris

How to Display M4000 XSCF IP from Solaris OS?

Hi All, I have an Oracle M4000 server with Solaris 10 OS. I have access to Solaris root prompt. But I don't know the XSCF IP of this server. Is there any way to display XSCF IP from Solaris OS? (2 Replies)
Discussion started by: byrusber
2 Replies
Tie::Array::Sorted(3pm) 				User Contributed Perl Documentation				   Tie::Array::Sorted(3pm)

NAME
Tie::Array::Sorted - An array which is kept sorted SYNOPSIS
use Tie::Array::Sorted; tie @a, "Tie::Array::Sorted", sub { $_[0] <=> $_[1] }; push @a, 10, 4, 7, 3, 4; print "@a"; # "3 4 4 7 10" DESCRIPTION
This presents an ordinary array, but is kept sorted. All pushes and unshifts cause the elements in question to be inserted in the appropri- ate location to maintain order. Direct stores ("$a[10] = "wibble"") effectively splice out the original value and insert the new element. It's not clear why you'd want to use direct stores like that, but this module does the right thing if you do. If you don't like the ordinary lexical comparator, you can provide your own; it should compare the two elements it is given. For instance, a numeric comparator would look like this: tie @a, "Tie::Array::Sorted", sub { $_[0] <=> $_[1] } Whereas to compare a list of files by their sizes, you'd so something like: tie @a, "Tie::Array::Sorted", sub { -s $_[0] <=> -s $_[1] } LAZY SORTING
If you do more stores than fetches, you may find Tie::Array::Sorted::Lazy more efficient. AUTHOR
Original author: Simon Cozens Current maintainer: Tony Bowden BUGS and QUERIES Please direct all correspondence regarding this module to: bug-Tie-Array-Sorted@rt.cpan.org This module was originall written as part of the Plucene project. However, as Plucene no longer uses this, it is effectively unmaintained. COPYRIGHT AND LICENSE
Copyright (C) 2003-2006 Simon Cozens and Tony Bowden. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. perl v5.8.8 2004-10-10 Tie::Array::Sorted(3pm)
All times are GMT -4. The time now is 07:17 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy