Sponsored Content
Full Discussion: M4000 fault
Operating Systems Solaris M4000 fault Post 302535612 by ctsgnb on Friday 1st of July 2011 09:36:38 AM
Old 07-01-2011
Hardware error ?
try to google on keys like "xscf fault (reason=0)"
Otherwise open a call to your vendor.
 

10 More Discussions You Might Find Interesting

1. Solaris

M4000 graphics card

Hi Guys, Anyone know any commands to verify the graphics card is installed correctly on an M4000? show-displays just comes back and echoes nothing. Also there is on input-device or output-device variable when you run printenv. This in itself is worrying. Any advice would be... (4 Replies)
Discussion started by: callmebob
4 Replies

2. UNIX for Dummies Questions & Answers

Help with restarting SUN m4000 server

I'm trying to power on our SUN m4000 server after a recent shutdown. When I try to connect to the xscf console I'm getting prompted for a password. The system is not asking for a login just a password. Below is the output from the xscf console. Anyone know how I can safely get back to the... (0 Replies)
Discussion started by: orahi001
0 Replies

3. Solaris

fmadm on an M4000

Hi people, Hoping someone has maybe done this before? I'm trying to run fmadm from the xcsf prompt on an M4000 and it won't run, complaining about insufficient privileges, even though the user has supposedly been setup with fieldeng privileges. Anyone got any ideas? Cheers Rgrds... (10 Replies)
Discussion started by: callmebob
10 Replies

4. Solaris

Single maintence mode cannot run any command on M4000

Hii All I was building two M4000 servers and one was successfully installed. Other one /usr has been unmounted. my putty session got disconnected and i connected to console where it asked for root single maintence # # init 0 not foung # df -h not found # xscf>poweroff -a xscf>... (8 Replies)
Discussion started by: seems
8 Replies

5. Solaris

M4000 Server Issue

Dear Team, This time i am facing some problems in Sun SPARC M4000 server. I have a doubt, when we are upgrading the firmware if XSCF , the OBP is also upgraded. What about server OBP, Is that upgardation need to be done separately ? what about DVD-ROM, HARD DISK firmware.... (3 Replies)
Discussion started by: sudhansu
3 Replies

6. Solaris

M4000 Memory Fault

Hi Guys and Gals, Does anyone know how to track down a faulty DIMM on the memory board of an M4000? showhardconf tells me which board it is, but was wondering if there was a way to track it down to a DIMM? Thanks in advance Martin (5 Replies)
Discussion started by: callmebob
5 Replies

7. Programming

Using gdb, ignore beginning segmentation fault until reproduce environment segmentation fault

I use a binary name (ie polo) it gets some parameter , so for debugging normally i do this : i wrote script for watchdog my app (polo) and check every second if it's not running then start it , the problem is , if my app , remain in state of segmentation fault for a while (ie 15 ... (6 Replies)
Discussion started by: pooyair
6 Replies

8. Solaris

M4000 Mode Switch

Hello, I'm set to go out to our M4000 to reset the XSCF password, since the person who set it up doesn't remember what password they setup. I have all the steps, but the only question I can't find an answer to is around the mode switch. Right now, based on prtdiag, the mode switch is in... (2 Replies)
Discussion started by: QuickNull
2 Replies

9. Solaris

CPU/processor/cores in M4000

Hi Gurus Can someone help me in explaining the below outputs . psrinfo -p 4 /usr/sbin/psrinfo -pv The physical processor has 4 virtual processors (0-3) SPARC64-VI (portid 1024 impl 0x6 ver 0x93 clock 2150 MHz) The physical processor has 4 virtual processors (8-11) SPARC64-VI... (3 Replies)
Discussion started by: ningy
3 Replies

10. Solaris

How to Display M4000 XSCF IP from Solaris OS?

Hi All, I have an Oracle M4000 server with Solaris 10 OS. I have access to Solaris root prompt. But I don't know the XSCF IP of this server. Is there any way to display XSCF IP from Solaris OS? (2 Replies)
Discussion started by: byrusber
2 Replies
dpkg-vendor(1)							    dpkg suite							    dpkg-vendor(1)

NAME
dpkg-vendor - queries information about distribution vendors SYNOPSIS
dpkg-vendor [option...] command DESCRIPTION
dpkg-vendor is a tool to query information about vendors listed in /etc/dpkg/origins. /etc/dpkg/origins/default contains information about the current vendor. COMMANDS
--is vendor Exits with 0 if the current vendor is vendor. Otherwise exits with non-zero. --derives-from vendor Exits with 0 if the current vendor distribution is a derivative of vendor, otherwise exits with non-zero. It uses the "Parent" field to browse all ancestors of the current vendor. --query field Print on standard output the value of the vendor-specific field for the current vendor. --help Show the usage message and exit. --version Show the version and exit. OPTIONS
--vendor vendor Assumes the current vendor is vendor instead of discovering it with the DEB_VENDOR environment variable or /etc/dpkg/ori- gins/default. ENVIRONMENT
DEB_VENDOR This setting defines the current vendor. If not set, it will discover the current vendor by reading /etc/dpkg/origins/default. SEE ALSO
deb-origin(5). Debian Project 2011-11-10 dpkg-vendor(1)
All times are GMT -4. The time now is 07:03 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy