07-01-2011
M4000 fault
Hi Guys and Gals,
Can someone help me possible?
Trying to power up an M4000 and it comes up with xscf fault (reason=0) it then just hangs there.
Any help would be gratefully appreciated.
Thanks
Martin
10 More Discussions You Might Find Interesting
1. Solaris
Hi Guys,
Anyone know any commands to verify the graphics card is installed correctly on an M4000?
show-displays just comes back and echoes nothing.
Also there is on input-device or output-device variable when you run printenv.
This in itself is worrying.
Any advice would be... (4 Replies)
Discussion started by: callmebob
4 Replies
2. UNIX for Dummies Questions & Answers
I'm trying to power on our SUN m4000 server after a recent shutdown. When I try to connect to the xscf console I'm getting prompted for a password. The system is not asking for a login just a password. Below is the output from the xscf console.
Anyone know how I can safely get back to the... (0 Replies)
Discussion started by: orahi001
0 Replies
3. Solaris
Hi people,
Hoping someone has maybe done this before?
I'm trying to run fmadm from the xcsf prompt on an M4000 and it won't run, complaining about insufficient privileges, even though the user has supposedly been setup with fieldeng privileges.
Anyone got any ideas?
Cheers
Rgrds... (10 Replies)
Discussion started by: callmebob
10 Replies
4. Solaris
Hii All
I was building two M4000 servers and one was successfully installed.
Other one /usr has been unmounted. my putty session got disconnected and i connected to console where it asked for root single maintence
#
# init 0
not foung
# df -h
not found
#
xscf>poweroff -a
xscf>... (8 Replies)
Discussion started by: seems
8 Replies
5. Solaris
Dear Team,
This time i am facing some problems in Sun SPARC M4000 server. I have a doubt, when we are upgrading the firmware if XSCF , the OBP is also upgraded.
What about server OBP, Is that upgardation need to be done separately ?
what about DVD-ROM, HARD DISK firmware.... (3 Replies)
Discussion started by: sudhansu
3 Replies
6. Solaris
Hi Guys and Gals,
Does anyone know how to track down a faulty DIMM on the memory board of an M4000?
showhardconf tells me which board it is, but was wondering if there was a way to track it down to a DIMM?
Thanks in advance
Martin (5 Replies)
Discussion started by: callmebob
5 Replies
7. Programming
I use a binary name (ie polo) it gets some parameter , so for debugging normally i do this :
i wrote script for watchdog my app (polo) and check every second if it's not running then start it , the problem is , if my app , remain in state of segmentation fault for a while (ie 15 ... (6 Replies)
Discussion started by: pooyair
6 Replies
8. Solaris
Hello,
I'm set to go out to our M4000 to reset the XSCF password, since the person who set it up doesn't remember what password they setup.
I have all the steps, but the only question I can't find an answer to is around the mode switch. Right now, based on prtdiag, the mode switch is in... (2 Replies)
Discussion started by: QuickNull
2 Replies
9. Solaris
Hi Gurus
Can someone help me in explaining the below outputs .
psrinfo -p
4
/usr/sbin/psrinfo -pv
The physical processor has 4 virtual processors (0-3)
SPARC64-VI (portid 1024 impl 0x6 ver 0x93 clock 2150 MHz)
The physical processor has 4 virtual processors (8-11)
SPARC64-VI... (3 Replies)
Discussion started by: ningy
3 Replies
10. Solaris
Hi All,
I have an Oracle M4000 server with Solaris 10 OS. I have access to Solaris root prompt.
But I don't know the XSCF IP of this server.
Is there any way to display XSCF IP from Solaris OS? (2 Replies)
Discussion started by: byrusber
2 Replies
LEARN ABOUT NETBSD
powerhook_disestablish
POWERHOOK_ESTABLISH(9) BSD Kernel Developer's Manual POWERHOOK_ESTABLISH(9)
NAME
powerhook_establish, powerhook_disestablish -- add or remove a power change hook
SYNOPSIS
void *
powerhook_establish(const char *name, void (*fn)(int why, void *a), void *arg);
void
powerhook_disestablish(void *cookie);
DESCRIPTION
The powerhook_establish API is deprecated.
The powerhook_establish() function adds fn of the list of hooks invoked by dopowerhooks(9) at power change. When invoked, the hook function
fn will be passed the new power state as the first argument and arg as its second argument.
The powerhook_disestablish() function removes the hook described by the opaque pointer cookie from the list of hooks to be invoked at power
change. If cookie is invalid, the result of powerhook_disestablish() is undefined.
Power hooks should be used to perform activities that must happen when the power situation to the computer changes. Because of the environ-
ment in which they are run, power hooks cannot rely on many system services (including file systems, and timeouts and other interrupt-driven
services). The power hooks are typically executed from an interrupt context.
The different reasons for calling the power hooks are: suspend, standby, and resume. The reason is reflected in the why argument and the
values PWR_SOFTSUSPEND, PWR_SUSPEND, PWR_SOFTSTANDBY, PWR_STANDBY, PWR_SOFTRESUME, and PWR_RESUME. It calls with PWR_SOFTxxx in the normal
priority level while the other callings are protected with splhigh(9). At suspend the system is going to lose (almost) all power, standby
retains some power (e.g., minimal power to USB devices), and at resume power is back to normal.
RETURN VALUES
If successful, powerhook_establish() returns an opaque pointer describing the newly-established power hook. Otherwise, it returns NULL.
SEE ALSO
dopowerhooks(9)
BSD
May 14, 2009 BSD