I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
I have installed Solaris 10 in my PC successfully and my system having Intel(R) PRO/100 VE ethernet card. Solaris OS not able to detect the network card. So i checked the driver (INTCGigaE) and reinstalled. Still network card is not detected.
bash-3.00# pkgchk INTCGigaE
ERROR:... (0 Replies)
Hi,
I want to create a file named 'abc(+1)' and append the data of file 'abc' to it. But getting error as unexpected'(' when i tried to use the following command.
cat abc > abc(+1)
Is there any other way to include brackets along with +1 in the file name?
TIA. (3 Replies)
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT REDHAT
sndconfig
sndconfig(8) System Manager's Manual sndconfig(8)NAME
sndconfig - configure sound card for use with Linux kernel modules
SYNOPSIS
sndconfig {--help,--noprobe,--noautoconfig}
DESCRIPTION
sndconfig sets up the necessary configuration files to use a sound card on a Red Hat system. If PnP support is compiled in, by default snd-
config will do an initial probe for PnP sound cards using the pnpdump utility. If the --noprobe option is given this step will be skipped.
The user will be notified if any cards were found. Otherwise the user must pick the card type from a menu. Then the user must choose the
I/O port, IRQ, and DMA settings for the sound card. These must be known ahead of time and depend upon the jumper settings of the sound
card. For PnP cards, the program will determine settings for the card; if the --noautoconfig option is given the user can choose the val-
ues which will be programmed into the PnP device. There is no guarantee that the values entered do not conflict with an existing non-PnP or
PnP device. The user must make sure these types of conflicts do not occur.
OPTIONS
--help Print a usage message on standard output and exit successfully.
--noprobe
No probe will be made for PnP cards, and the PnP configuration files will not be changed.
--noautoconfig
No autoconfiguration of PnP cards will be done; the user will be prompted for settings.
FILES
/etc/sysconfig/soundcard Stores current settings /etc/modules.conf Stores sound module configuration /etc/isapnp.conf Stores
PnP configuration
SEE ALSO isapnp(1), pnpdump(1)
Wed Aug 19 1998 sndconfig(8)