06-28-2011
Network card naming issue
I have a Sun server running SuSE with 2 network cards, the cards naming is eth0-to-eth3 for the first card, and eth4-eth7 for the second one, I've replace the second card and I got naming issue: I got eth4, eth5, eth7, eth8 I mean the system doesn't see eth6 so it took eth7 instead, is there a way to fix this, in other word is there a way to rename the interfaces [ethxx] or to clear the system config then the system will take them automatically in the right order.
Thank you guys
(^_^)
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
3. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
I have installed Solaris 10 in my PC successfully and my system having Intel(R) PRO/100 VE ethernet card. Solaris OS not able to detect the network card. So i checked the driver (INTCGigaE) and reinstalled. Still network card is not detected.
bash-3.00# pkgchk INTCGigaE
ERROR:... (0 Replies)
Discussion started by: paventhan
0 Replies
7. Shell Programming and Scripting
Hi,
I want to create a file named 'abc(+1)' and append the data of file 'abc' to it. But getting error as unexpected'(' when i tried to use the following command.
cat abc > abc(+1)
Is there any other way to include brackets along with +1 in the file name?
TIA. (3 Replies)
Discussion started by: vimalr
3 Replies
8. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT DEBIAN
aoe-discover
aoe-discover(8) System Manager's Manual aoe-discover(8)
NAME
aoe-discover - tell aoe driver to discover AoE devices
SYNOPSIS
aoe-discover
DESCRIPTION
The aoe-discover command tells the aoe driver to discover ATA over Ethernet (AoE) devices on the network. All network interfaces will be
probed with a AoE config query broadcast.
If the aoe-interfaces command has limited the allowable network interfaces, only devices discovered via allowable interfaces will become
available. The default is to make available all AoE devices found on all accessible ethernet networks.
It's good to run the aoe-discover command after running aoe-interfaces.
EXAMPLE
In this example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic. After remembering that
shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then calls aoe-discover
to ask the aoe driver to look for new AoE devices.
nai:~# modprobe aoe aoe_iflist="eth0"
nai:~# aoe-stat
e10.9 eth0 up
nai:~# aoe-interfaces eth0 eth3
nai:~# aoe-discover
nai:~# aoe-stat
e7.0 eth3 up
e7.1 eth3 up
e7.2 eth3 up
e7.3 eth3 up
e7.4 eth3 up
e7.5 eth3 up
e7.6 eth3 up
e7.7 eth3 up
e7.8 eth3 up
e7.9 eth3 up
e10.9 eth0 up
SEE ALSO
aoe-interfaces(8), aoe-stat(8), aoetools(8).
AUTHOR
Ed L. Cashin (ecashin@coraid.com)
aoe-discover(8)