06-27-2011
Print pattern range to a new file
Hi Everyone!
I really appreciate all of your help, I'm learning so much, can't wait until I get good enough to start answering questions!
I have a problem ... from one large file, I'd like to create multiple new files for each pattern block
beginning with /^ISA/
ending with /^IEA/
I'd even be happy with creating a new file for everything up to and including each occurence of ISA.
File is too big for csplit, I get a virtual memory exhausted error ... so I was thinking perl or awk? But I'm too new to both.
Again, I really appreciate your taking the time to help and answer questions
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I need to list only file names of a specific date from the command ls -lt.
:confused: (2 Replies)
Discussion started by: Shamwari
2 Replies
2. Shell Programming and Scripting
I want to print between the range two patterns if a particular pattern is present in between the two patterns. I am new to Unix. Any help would be greatly appreciated.
e.g.
Pattern1
Bombay
Calcutta
Delhi
Pattern2
Pattern1
Patna
Madras
Gwalior
Delhi
Pattern2
Pattern1... (2 Replies)
Discussion started by: joyan321
2 Replies
3. Shell Programming and Scripting
Hi,
My input has much more lines, but few of them are below
pin(IDF) {
direction : input;
drc_pinsigtype : signal;
pin(SELDIV6) {
direction : input;
drc_pinsigtype : ... (3 Replies)
Discussion started by: nehashine
3 Replies
4. Shell Programming and Scripting
Scenario:
Each of several .txt files contain the following (but perhaps with some minor variations due to code version running on the devices from which the text was extracted):
<output omitted>
SWITCH1#show proc cpu hist
1... (4 Replies)
Discussion started by: svermill
4 Replies
5. Shell Programming and Scripting
Hi all,
on Solaris 10, I'd like to print a range of lines starting at pattern but also including the very first line before pattern.
the following doesn't print the range starting at pattern and going down to the end of file: cat <my file> | sed -n -e '/<pattern>{x;p;}/'
I need to include the... (1 Reply)
Discussion started by: siriche
1 Replies
6. Shell Programming and Scripting
Hi,
I have a file as below
This is the line one
This is the line two
<\XMLTAG>
This is the line three
This is the line four
<\XMLTAG>
Output of the SED command need to be as below.
This is the line one
This is the line two
<\XMLTAG>
Please do the need to needful to... (4 Replies)
Discussion started by: RMN
4 Replies
7. Shell Programming and Scripting
The following text is in testFile.txt:
one 5
two 10
three 15
four 20
five 25
six 10
seven 35
eight 10
nine 45
ten 50
I'd like to use sed to print the first occurance of search pattern /10/ in a given range. This command is to be run against large log files, so to optimize efficiency,... (9 Replies)
Discussion started by: uschaafm
9 Replies
8. Shell Programming and Scripting
I have config file like this:
server_name xx opt1 opt2 opt3
suboptions1
#suboptions - disabled
suboptions2 pattern
suboptions3
server_name yy opt1 opt2 opt3
suboptions1 pattern
#suboptions - disabled
suboptions2
So basically I want to extract the server... (1 Reply)
Discussion started by: nemesis911
1 Replies
9. Shell Programming and Scripting
In the awk below I am trying to print out those lines in file2 that are no between $2 and $3 in file1. Both files are
tab-delimeted and I think it's close but currently it is printeing out the matches. The --- are not part of the files they are just to show what lines match or fall into
the range... (6 Replies)
Discussion started by: cmccabe
6 Replies
10. Shell Programming and Scripting
I have big files (some are >300GB!) that need substitution for some patterns, for example, change Multiple Spaces into Tab. I used this oneliner:sed '1,18s/ \{1,\}/\t/g' infile_big.sam > outfile_big.sambut it seems very slow as the job is still running after 24 hours! In this example, only the... (8 Replies)
Discussion started by: yifangt
8 Replies
PNP(4) BSD/i386 Kernel Interfaces Manual PNP(4)
NAME
pnp -- support for ``Plug and Play'' (PnP) ISA devices
DESCRIPTION
The pnp driver enumerates ISA devices which support ``Plug and Play ISA Specification'' in the system. It assigns ISA bus resources (inter-
rupt line, DMA channel, I/O ports, and memory region) to each device and activates it.
If it cannot assign necessary resources to a PnP ISA device without causing conflict with other devices in the system, the device will not be
activated and will be unavailable to programs.
CAVEATS
It is not possible to disable individual PnP ISA devices. The pnp driver will find all devices conforming the PnP ISA specification and try
to activate them all.
There is no way to explicitly assign particular resource to the PnP ISA device. The resource assignment is fully automatic and there is no
provision for manual override.
SEE ALSO
pnpbios(4)
STANDARDS
Intel and Microsoft, Plug and Play ISA Specification, Version 1.0a, May 5, 1994.
Clarifications to the Plug and Play ISA Specification, Version 1.0a, December 10, 1994.
HISTORY
The pnp driver first appeared in FreeBSD 2.2.5. It has been substantially updated in subsequent versions.
AUTHORS
PnP support was originally written for FreeBSD 2.2.5 by Luigi Rizzo, based on initial work done by Sujal Patel.
BSD
September 20, 2001 BSD