Lets say a user starts a process (either a shell script or a Perl script) and before that process finishes, he logs out (either intentionaly or network problems or ...), does the process continu running ?
Default shell is Korn.
This is because at my job (being trained), there are tasks to run... (2 Replies)
Hello All,
I am trying to write a script that will only continue executing my script if a file exits. I know the directory of the file, so its just a matter of seeing if the file exists yet. If the file has not yet been created, I want the script to wait 10 minutes (600 seconds) and try again.... (7 Replies)
HI ,
I am new to the perl , I am using a if condition and in that if condition i am checking 7 variables value. so it continue to second line .And if i user "\" for the continue line it showing error.
Example :
if(a >9 || b>8 || c> 10 \
d > 11)
{
print();
}
The above statement is... (3 Replies)
Hi,
We put cron entry :whenever server is offline(checks every 5 minutes) it sends status to mailer group.
The number of messages (offline)were growing in our mailbox.How to avoid not to send offline messages after the first one through shell script.
Thanks in advance.
Chowdary (2 Replies)
Hello, I am writing a script and in this script, I want to be able to have the script continue running if the correct word is not entered...
Here is an excerpt from me script:
read request
if ;
then
echo "You have asked for the System Temperature..."
cat... (1 Reply)
Hello all,
I am trying to do a tail in a script. But when I quit the tail my script quits also. This is not what I want. I am struggling to get this done.
#!/bin/bash
askFile() {
echo -n "Enter file: "
read FILE
}
doTail() {
tail -F "${1}"
}
askFile
doTail... (4 Replies)
How can I get a script to complete a update, varifiy completion, resboot, and continue with script?
Is it possbile to get script to add itself to the "startup application" list
#!/bin/bash
clear
sudo apt-get update
#Verify/test the update completed
#Reboot
#Start/comtinue... (9 Replies)
Hello,
I have a very long instruction to write, but, for lisibility reasons, I would like to cut it on more than one line and comment each lines.
is it possible ?
thanks :b: (1 Reply)
:eek:Below is my code to create a user account but it doesn't take a password automatically. I have to run the password command seperately to do this
What I want to do is to be able to accept the password in a script.
In linux with the "useradd' command you can give the "-p" flag to accept the... (3 Replies)
Hi,
I am writing a shell script where I am sourcing other shell script in that script I have mention exit 0 due to that it is not continue the first script. Except doing any changes to source script is there any way I can continue the my first script. (3 Replies)
Discussion started by: sonujatav
3 Replies
LEARN ABOUT NETBSD
nohup
NOHUP(1) BSD General Commands Manual NOHUP(1)NAME
nohup -- invoke a command immune to hangups
SYNOPSIS
nohup utility [arg ...]
DESCRIPTION
The nohup command allows the specified utility to be protected from termination if the user should become logged out (for example, due to a
modem line or TCP/IP connection being dropped). To do this, nohup sets the SIGHUP signal(3) (``terminal line hangup'') to be ignored, then
executes utility along with any arguments.
If the standard output is a terminal, the standard output is appended to the file nohup.out in the current directory. If standard error is a
terminal, it is directed to the same place as the standard output. If the output file nohup.out cannot be created in the current directory,
nohup attempts to create the file in the user's home directory. If the file nohup.out cannot be created, either in the current directory or
the user's home directory, nohup will exit without invoking utility, with an exit value as described below.
ENVIRONMENT
The following variable is used by nohup.
HOME User's home directory.
EXIT STATUS
The nohup utility exits with one of the following values:
126 The utility was found but could not be invoked.
127 The utility could not be found or an error occurred in nohup.
Otherwise, the exit status of nohup will be that of utility.
SEE ALSO signal(3)STANDARDS
The nohup command is expected to be IEEE Std 1003.2 (``POSIX.2'') compatible.
BSD July 15, 2005 BSD