06-23-2011
One reason is ease of IP address management
10 More Discussions You Might Find Interesting
1. HP-UX
***Newbie alert***
What's the easiest way to accomplish this? An admin left our company and I have taken over his HP Workstation and moved it to a different location that is on a different IP segment.
I have performed a number of google searches but the steps I have followed haven't worked.
... (1 Reply)
Discussion started by: Steelysteel
1 Replies
2. IP Networking
I have a USB Wireless Adapter using the rum0 driver. All I want to do is set a perminent static IP for the onboard wired interface elxl0. I can plumb the wired interface up fine on the fly, but when I try to save the static IP over a reboot, I lose the IP address assigned to rum0 from my wireless... (1 Reply)
Discussion started by: ts97783
1 Replies
3. IP Networking
I am pretty new to this. My router was earlier configured to enable DHCP, thus my UNIX box is using the dhcp address, i.e. I have to do a ifconfig dhcp hme0 start. Since I am planning to use my NT as a web server, I needed to use the static IP address. How do I configure the unix box to use the... (5 Replies)
Discussion started by: lee30320
5 Replies
4. IP Networking
I am trying to write a set of scripts for my Ubuntu 810 Server to allow a user to change from DHCP to a user-supplied Static IP, Subnet, Gateway and DNS Servers.
So far I have the following, where $USERCHOICE is a user-entered value in each case:
ifconfig eth0 down && ifconfig eth0 $USERCHOICE... (1 Reply)
Discussion started by: cleanden
1 Replies
5. Red Hat
Hi,
I am using RHEL 5.1 and i would like to know,
how to find the whether my system is using DHCP or STATIC IP
with out looking at /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file.
Regards,
Venkat (3 Replies)
Discussion started by: venkat55
3 Replies
6. UNIX for Dummies Questions & Answers
Hey guys ,
YEs this is probably silly for most but i am new to this forum and solaris . i am curious to know if the ip address we have for our solaris server is static or dhcp . how can i tell ? will ifconfig -a tell me this ? or other commands?
Thanks in advance (1 Reply)
Discussion started by: xdrivex
1 Replies
7. HP-UX
Hi,
I can find the IP details whether it is Static or dynamic in Linux machine from the location /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file.
Can someone suggest a location to find the same in HP UX machines?
-Vivek (2 Replies)
Discussion started by: vkk
2 Replies
8. IP Networking
Hi All ,
please view the set up below:
-------------------------------------------------------------------
| DHCP Server |-----------| ROUTER & |-----------| Clients |
| 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X |
... (2 Replies)
Discussion started by: gdangoor
2 Replies
9. IP Networking
I'm trying to figure out what circumstances would cause an Open Solaris 11.2 host to switch itself from a static to a DHCP ip address upon reboot. This has only happened once but is a cause for some concern as this machine will be part of a web server pool.
Nothing has changed on the LAN that... (2 Replies)
Discussion started by: SmokeyJoe
2 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
bptojdb(8) System Manager's Manual bptojdb(8)
NAME
bptojdb - Converts bootptab entries into permanent, static IP entries for JOIN databases.
SYNOPSIS
/usr/sbin/bptojdb [-m | -f] filename
OPTIONS
Create client IDs for Microsoft DHCP clients. Microsoft does not use the client's MAC address by itself as the client identifier.
Instead, it prepends a 01 (Ethernet) to the MAC address and changes the hardware type to 0 (generic). If the clients in your bootptab file
are Microsoft clients, you will need to use the -m option. Create client IDs for FTP Software's DHCP clients. FTP Software does not use
the client's MAC address by itself as the client identifier. Instead, it creates a 16-byte client identifier with the prefix "cid-". If
the clients in your bootptab file are FTP Software DHCP clients, you will need to use the -f option.
DESCRIPTION
The bptojdb program reads entries in a standard bootptab file and creates permanent, static IP entries for the JOIN databases. After read-
ing the bootptab file, bptojdb displays to the standard output entries in a format suitable for the jdbmod utility. Each MAC address in the
bootptab file is given a static IP address with a permanent lease. To store the information in the JOIN databases, run jdbmod with the
converted data. For example: bptojdb bootptab | jdbmod
FILES
SEE ALSO
Commands: jdbdump(8), jdbmod(8)
bptojdb(8)