06-20-2011
I have tried your solution, but it doesnt seem to be running.But I have an idea, to get ping result from ping6 command from linux it self. The problem is, I still dont understand how to grep the ping result from this command, whether reply,request timed out, or destination unreachable? Somebody told me to use regex on perl. But I still confused, what kind of regex that I have to use..
Any solutions??
Thanks in advance,
Franz
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
2. AIX
hello
i'm working on AIX 5300-05-03 P520 hacmp 5.4
when connection to the internet is going down , firewall down, my application work verey verey slowly!!! and on the sliffer output i'm got trys of my serevr to do convert from ipv4 ipv6 ( 0.0.2.0 and AAAAAAAA).
some one have an idea why... (1 Reply)
Discussion started by: ariec
1 Replies
3. IP Networking
Need help...!
I want to configure Samba 3 for IPv6 operation with Window XP for IPv4.
I appreciate any guide.
Thanks
HSV (0 Replies)
Discussion started by: Sovan
0 Replies
4. Solaris
Hi folks, i hope you'll help me to configure my ipv6 tunnel.
First, i create my tunnel in:
Hurricane Electric Free IPv6 Tunnel Broker
My IP is 83.228.93.34
in HE:
------------------------
Server IPv4 address: 216.66.84.46
Server IPv6 address: 2001:470:1f14:16a::1/64
Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies
5. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
6. Solaris
Hi
I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC,
finding the ipv4 options for the SUN DHCP options was ok eg
TFTPsrvN = tftp-server-name
OptBootF = bootfile-name
However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies
7. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
8. Solaris
Hi,
I am looking for a solution to configure ntp between ipv4 ( ntp server ) to ipv6 ( client) .
I had google, but lot many sites suggest to have dual stock or tunnaling.
my issue is I have client has only ipv6 address ans server has ipv4 address. is it possible to sync time,... (4 Replies)
Discussion started by: naveen.surisett
4 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies