06-18-2011
broadcom drivers and the kernel break each other, every other release. You might have to either wait for a fix or try downloading/building a newer broadcom driver manually.
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
First of all, excuse my ignorance in my questions, but truth is, I know nothing about Unix. I have recently purchased some A7012A's (dual port, 1000 base T/X) gigabit cards and need to use them in a windows environment.
I am trying to see if it is possible to have drivers written for the card... (0 Replies)
Discussion started by: poaking
0 Replies
2. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
3. Hardware
hi,
would anyone know where to get a Linux ( Red Hat ) driver for a SafeCom ( i.e. Texas Instruments ) 11g WLAN card SWLPT 54108 ?
It's quite an old card that only seems to come with windows drivers on its install disk.
thanks,
Jim (1 Reply)
Discussion started by: jimthompson
1 Replies
4. Solaris
I have OptiPlex machine which has Integrated Intel® I217LM Ethernet LAN 10/100/1000 interface. When I am trying to install Solaris 10U11 during the installation it dint ask for networking configuration. I installed the OS and found that Solaris dont show any interface through ifconfig -a plumb.... (7 Replies)
Discussion started by: linuxfreaker
7 Replies
5. Shell Programming and Scripting
Hi Everybody,
Goal:
From my backup box on my local network, knowing the Wifi MAC address of my laptop, I would like to dynamically identify which ip address is attributed to my laptop.
The aim is to store this ip address in a local variable and that this information is retrieved by another... (11 Replies)
Discussion started by: freddie50
11 Replies
6. Debian
Hi, I am Konrad , I am a new user of this forum.
I am from Poland, so my English isn't good enough. So please be forgiving for me.
I read about Bits club or something like that, So I don't know, that I am allowed to write here.
But nevertheless I have faced with small problem with wifi driver on... (4 Replies)
Discussion started by: kondziorek
4 Replies
7. Solaris
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
8. Hardware
I have hp dv6 and dv7 notebook pcs on which I want to upgrade the wifi cards but when I install the new cards and boot them, the they won't even boot to the bios and they both give me the same error: "104-Unsupported wireless network device detected. System Halted. Remove device and restart." When... (1 Reply)
Discussion started by: milhan
1 Replies
9. Linux
After installing the latest version of Kali on my Lenovo S21E laptop, I cannot access the internet.
wlan0 does not show up in ifconfig and I cannot connect to the internet.
If you need any other additional information, I will provide it. Thank you kindly. (8 Replies)
Discussion started by: Hotrod22
8 Replies
ndd(1M) System Administration Commands ndd(1M)
NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)
NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)