Hi Does anyone know the command to configure HP tape slots. I have tried the following on Sun, but its notworking. This is the first time I have configured a tape drive with muiltple slots.
root@ssdb0009 # cfgadm -l
Ap_Id Type Receptacle Occupant Conditio... (3 Replies)
Hello,
I'm running Red Hat Linux on a Dell Poweredge 2650 Rack Server and wondered if anyone knew of a tool or command I could use to probe the memory slots on the motherboard.
I know the machine has six memory slots and currently contains 1GB RAM, what I don't know however, is if it contains... (3 Replies)
Due to speed mismatch, the server kept crashing. Sun suggests that I need to move the two HBA cards from the 66Mhz to the 33Mhz slots. There are tons of disks that are connected to these HBAs and I have Veritas volume manager.
Does anyone have a list of what I need to do prior/after moving to... (3 Replies)
I'm looking for open PCI slots in our array of sun boxes. I need help on how to distinguish if there's an open slot or not using prtdiag and prtconf. Is there a better tool for this? TIA.
Here's my prtdiag -v | grep pci:
pci 66 PCI5 SUNW,qlc-pci1077,2312 (scsi-+
... (9 Replies)
A while back I had a command that shows the memory slots (and info on the modules inserter) in an IBM AIX machine. I cannot remember it at this time, can someone help me out with this command please? (4 Replies)
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
I tried to reinstall GRUB2 on my previous Solaris 11.3 installation but could not figure out why "bootadm install-bootloader" failed. Now I am trying to reinstall Solaris 11.3 instead, over my old Solaris partition. I am using the USB Live media ISO with the GUI. Installation fails with this... (0 Replies)
Discussion started by: kebabbert
0 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)