06-09-2011
Quote:
Did u checked whether your disks (sd [b|c] ) are available after the reboot...
yep... i couldnt find any disk array but the disks(sd [b|c] ) are available!!!
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Percent complete SCO 5.0.6 / No longer an issue (0 Replies)
Discussion started by: Henrys
0 Replies
2. AIX
I created a RAID 5 array and when I list out the attributes of the "hdisk" it reports back raid_level = 5 but the RAID level of the array = false. What does this actually indicate about my array? I've never paid much attention to this until now since I have a disk reporting failure I want to make... (0 Replies)
Discussion started by: scottsl
0 Replies
3. UNIX for Advanced & Expert Users
Hi guys,
i must install an old old old ml370 server...
I must create a RAID 5 with my 4 SCSI disk.
I need a SmartStart disk for create it or a Floppy Disk called "Array configuration Tool". I don't find it on the hp website...:mad::mad::mad:
Anyone have it??
Thanks in advance.
Zio (0 Replies)
Discussion started by: Zio Bill
0 Replies
4. Solaris
Hi Peeps,
Can anyone help me an EFI lablel on a 3510 raid array that I cannot get rid of, format -e and label just asks you if you want to label it. Want an SMI label writing to it.
Anyone got any ideas on how to remove the EFI label?
Thanks in advance
Martin (2 Replies)
Discussion started by: callmebob
2 Replies
5. Emergency UNIX and Linux Support
One of my very old drive farm servers had an OS fault and can't boot now but I'd like to restore some files from it. I tried booting Ubuntu from a CD, but it couldn't see the drives -- possibly because they're RAIDed together. Is there a good way to get at my files?
The data in question is a... (2 Replies)
Discussion started by: CRGreathouse
2 Replies
6. Solaris
Hi, Here is the issue: There are 4 disks on this Sun x4150 system under Solaris 10, but only 1 disk can be seen by the OS. I've tried commands disks and devfsadm but not working. It's an important production server, so 'reboot -r' is not a choice.
# format < /dev/null
Searching for... (6 Replies)
Discussion started by: aixlover
6 Replies
7. Fedora
Hello world,
One of the servers, a Fedora one,rebooted today (Luckily, a testbox).
I tried to get the reason the server rebooted. After going through the messages, I think that the log entries just before and after reboot are missing.
Please below: (****** is the server name, for privacy... (0 Replies)
Discussion started by: satish51392111
0 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. UNIX for Advanced & Expert Users
Thank you in advanced,
I had a Buffalo DUO crap out on me that was setup as RAID 0. I dont belive it was the drives but rather the controller in the DUO unit. I bought another external HDD enclosure and was able to fireup the two older DUO drives in it and I think I resembled the RAID... (12 Replies)
Discussion started by: metallica1973
12 Replies
vxpfto(1M) vxpfto(1M)
NAME
vxpfto - set Powerfail Timeout (pfto)
SYNOPSIS
vxpfto -g diskgroup -t timeout
vxpfto [-g diskgroup] -t timeout volume_list
vxpfto [-g diskgroup] -o pftostate={enabled|disabled}
vxpfto [-g diskgroup] -o pftostate={enabled|disabled} volume_list
DESCRIPTION
Powerfail Timeout is an attribute of a SCSI disk connected to an HP-UX host (see the pfto(7) man page). The vxpfto command sets the Power-
fail Timeout interval on a set of Volume Manager disks, either all disks in a disk group, or all disks underlying the volumes listed.
The first form of the command sets the same PFTO value for all the disks in the specified VxVM diskgroup.
In the second form, all disks underlying the given list of volumes are selected, optionally restricted by the disk group specified with the
-g option. If you specify a diskgroup, any volume in the list not belonging to the diskgroup is ignored.
Use the -o pftostate option to disable or enable PFTO. By default, PFTO is enabled. You can enable PFTO either on all disks in a disk
group, or on all disks underlying the volumes listed.
If you invoke vxpfto without arguments, it displays a usage message.
OPTIONS
-g diskgroup
Specifies the disk group for the operation, either by disk group ID or by disk group name.
-o pftostate={enabled|disabled}
Enables or disables the use of PFTO for IO.
-t timeout
Specifies the PFTO value in seconds. The value must be zero or a positive integer. Zero represents the system default PFTO
value. The default value depends on the disk driver controlling the disk device.
volume_list
A list of VxVM volume names. List items must be separated by white-space.
EXIT CODES
vxpfto returns a zero if successful. If it encounters an error, vxpfto exits and displays a message on standard error. Defined exit codes
are:
0 Success.
1 No PFTO value specified.
2 No diskgroup or volume list specified.
3 Illegal PFTO value specified.
EXAMPLES
Set the PFTO value on all disks in disk group testdg to 100 seconds:
vxpfto -t 100 -g testdg
Set the PFTO value to 50 seconds on all disks underlying volume01 and volume02 in disk group testdg:
vxpfto -t 50 -g testdg volume01 volume02
Set the PFTO value to 300 seconds on all disks underlying volume01 and volume02, even though they are not in the same disk group:
vxpfto -t 300 volume01 volume02
Disable PFTO on all disks in disk group testdg:
vxpfto -g testdg -o pftostate=disabled
Enable PFTO on all disks underlying volume01 and volume02i in disk group testdg:
vxpfto -g testdg -o pftostate=enabled volume01 volume02
SEE ALSO
vxdisk(1M), pfto(7)
VxVM 5.0.31.1 24 Mar 2008 vxpfto(1M)