i ve configured raid 0 in redhat machine(VM ware), by following steps:
then
mounted the/dev/md0 device and also added a entry in fstab.
how the isssue is when the system rebooted the raid array configuration is missing, there is no device as /dev/md0..
what's the solution for this??? any help !!!!
Last edited by pludi; 06-08-2011 at 07:06 AM..
Reason: content editing...
I created a RAID 5 array and when I list out the attributes of the "hdisk" it reports back raid_level = 5 but the RAID level of the array = false. What does this actually indicate about my array? I've never paid much attention to this until now since I have a disk reporting failure I want to make... (0 Replies)
Hi guys,
i must install an old old old ml370 server...
I must create a RAID 5 with my 4 SCSI disk.
I need a SmartStart disk for create it or a Floppy Disk called "Array configuration Tool". I don't find it on the hp website...:mad::mad::mad:
Anyone have it??
Thanks in advance.
Zio (0 Replies)
Hi Peeps,
Can anyone help me an EFI lablel on a 3510 raid array that I cannot get rid of, format -e and label just asks you if you want to label it. Want an SMI label writing to it.
Anyone got any ideas on how to remove the EFI label?
Thanks in advance
Martin (2 Replies)
One of my very old drive farm servers had an OS fault and can't boot now but I'd like to restore some files from it. I tried booting Ubuntu from a CD, but it couldn't see the drives -- possibly because they're RAIDed together. Is there a good way to get at my files?
The data in question is a... (2 Replies)
Hi, Here is the issue: There are 4 disks on this Sun x4150 system under Solaris 10, but only 1 disk can be seen by the OS. I've tried commands disks and devfsadm but not working. It's an important production server, so 'reboot -r' is not a choice.
# format < /dev/null
Searching for... (6 Replies)
Hello world,
One of the servers, a Fedora one,rebooted today (Luckily, a testbox).
I tried to get the reason the server rebooted. After going through the messages, I think that the log entries just before and after reboot are missing.
Please below: (****** is the server name, for privacy... (0 Replies)
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Thank you in advanced,
I had a Buffalo DUO crap out on me that was setup as RAID 0. I dont belive it was the drives but rather the controller in the DUO unit. I bought another external HDD enclosure and was able to fireup the two older DUO drives in it and I think I resembled the RAID... (12 Replies)
Discussion started by: metallica1973
12 Replies
LEARN ABOUT DEBIAN
sbp_targ
SBP_TARG(4) BSD Kernel Interfaces Manual SBP_TARG(4)NAME
sbp_targ -- Serial Bus Protocol 2 (SBP-2) Target Mode devices driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device sbp_targ
device firewire
device scbus
device targ
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
firewire_load="YES"
cam_load="YES"
sbp_targ_load"YES"
DESCRIPTION
The sbp_targ driver provides support for SBP-2 target mode. This driver is supposed to work with cam(4), targ(4) and firewire(4). You also
need to use scsi_target(8), which can be found in /usr/share/examples/scsi_target, to provide actual devices.
EXAMPLES
# mdconfig -a -t malloc -s 10m
md0
# scsi_target 0:0:0 /dev/md0
(Assuming sbp_targ0 on scbus0)
SEE ALSO cam(4), firewire(4), targ(4), camcontrol(8), fwcontrol(8), kldload(8), scsi_target(8)AUTHORS
The sbp_targ driver was written by Hidetoshi Shimokawa.
BUGS
This driver is currently under development. It does not work correctly in multi-initiator environments or after the bus topology has been
changed.
BSD November 7, 2003 BSD