Hi,
We are running a perl script to upload some data using SQL* Loader. We pipe the data in a http request to SQL*Loader which loads the data to the database. We encounter the error "Inappropirate ioctl for device" when we try to upload huge data. Any solution would be greatly appreciated.... (4 Replies)
When I try to format a slice in Solaris 10 I get the follow error :confused: :
-bash-3.00# mkfs /dev/dsk/c1d0s5 18877824
Can not determine partition size: Inappropriate ioctl for device
Some format command output:....
AVAILABLE DISK SELECTIONS:
0. c1d0 <DEFAULT cyl 38735 alt 2... (0 Replies)
Hello,
I have a cron entry:
59 23 * * * . $HOME/.profile;mydate=`date '+%Y%m%d'`;mv filename filename_$mydate
Which works fine interactively, but gives me the following error when it runs in cron:
Your "cron" job on servername
. $HOME/.profile;mydate=`date '+
produced the... (4 Replies)
When I try to format a slice in Solaris 10 I get the follow error :
-bash-3.00# mkfs /dev/dsk/c1d0s5 18877824
Can not determine partition size: Inappropriate ioctl for device
Some format command output:....
AVAILABLE DISK SELECTIONS:
0. c1d0 <DEFAULT cyl 38735 alt 2 hd 64 sec 63>... (2 Replies)
Dear all,
Problem goes like this:
I have a shell script which when run manually runs perfectly.
When same script is executed through a job schdeduler I get an error as Inappropriate ioctl for device and the script fails.
This problems seems quite guiling to me.
Any clues are heartly... (11 Replies)
Hello guys,
on my Red Hat machine the /bin/mt status command gives the output dev/tape: inappropriate ioctl for device. This messages comes up after the Server has been rebooted.
Anybody an idea?
Thx
masterofdesaster (8 Replies)
Hi All,
Am finding performance of my SD card using hdparm.
Code:
hdparm -tT /dev/BlockDev0
/dev/BlockDev0:
Timing cached reads: 1118 MB in 2.00 seconds = 558.61 MB/sec
HDIO_DRIVE_CMD(null) (wait for flush complete) failed: Inappropriate
ioctl for device
Timing buffered disk... (1 Reply)
Hi!
I am getting a nohup issue on mac osx while trying to start a process through nohup in the startup script.
nohup: can't detach from console: Inappropriate ioctl for device
Please help!
Thanks,
Allan. (0 Replies)
Hi,
ssh -q -t -l $usr $host bin/test.sh
I am using above command to run script remotely. script is working without any issues. but I am getting "tcgetattr: Inappropriate ioctl for device" message on console.
plz help how can I avoid this message.
Thanks
Moved thread from Emergency... (1 Reply)
Sample program tty, this will be get called from my script test_script.
#include <stdio.h>
#include <unistd.h>
#define TTY_NAME_MAX 32
#define STDIN_FILENO 0 /* Standard input. */
int main(void) {
int ret = 0;
char local_device_file;
printf("\npid =... (7 Replies)
Discussion started by: Gajendra_PH
7 Replies
LEARN ABOUT DEBIAN
gnunet-nat-server
GNUNET-NAT-SERVER(1) General Commands Manual GNUNET-NAT-SERVER(1)NAME
gnunet-nat-server - help GNUnet setup test network setup with NAT
SYNOPSIS
gnunet-nat-server [options] PORT
DESCRIPTION
Normal GNUnet end-users should not concern themselves with gnunet-nat-server. In fact, distributions are encouraged to consider not ship-
ping it at all. Running gnunet-nat-server's is similar to running hostlist servers: it is a special service to the community with special
requirements and no benefit to those running the service.
This program will listen on the specified PORT for incoming requests to test a peer's network connectivity. Incoming requests can ask it
to connect to a given IPv4 address (and port) using TCP or UDP and to send a 2-byte test message using the specified address. The program
can also be asked to send a "fake" ICMP response message to a given IPv4 address (for autonomous NAT traversal --- see the description in
the respective research paper).
The idea is that gnunet-nat-server will be run on some trusted hosts with unrestricted connectivity to allow GNUnet users to test their
network configuration. As written, the code allows any user on the Internet to cause the gnunet-nat-server to send 2-bytes of arbitrary
data to any TCP or UDP port at any address. We believe that this is generally harmless.
When running gnunet-nat-server, make sure to use a configuration that disables most NAT options but enables 'enable_nat_client' and sets
'internal_address' to the global IP address of your local host. Also, the gnunet-helper-nat-client should be installed locally and run
with root privileges (SUID), otherwise the gnunet-nat-server will not work properly.
Note that gnunet-nat-server could be run via gnunet-arm but typically is not. Also, the name of the host and port that gnunet-nat-server
is run on should be specified in the NATSERVER option in the [setup] section of the configuration file of hosts that are supposed to auto-
configure with this server.
OPTIONS -c FILENAME, --config=FILENAME
Use the configuration file FILENAME.
BUGS
Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>
SEE ALSO gnunet-transport(1)GNUnet 25 Feb 2012 GNUNET-NAT-SERVER(1)