06-01-2011
- Connect eth2 from both nodes to switch 1
- Connect eth3 from both nodes to switch 2
Now you have two paths available
- Enter the IP address of eth2 in the /etc/hosts file
example:
server-priv1 10.10.10.10
- edit the /etc/hostname.eth2 as follows:
server-priv1 netmask + broadcast + group ipmp0 up
- edit the /etc/hostname.eth3 as follows:
group ipmp0 up
Reboot the server
Note: Do not assign IP to the standby interface.
Note: Assuming you are using solaris10
use the following command to test ipmp via CLI
#if_mpadm [-r] [-d] <interface>
- -r -> revert back
- -d -> disable i-e failover
10 More Discussions You Might Find Interesting
1. IP Networking
i have one private network with one ip address, and i have a seperate network on a seperate ip address.
now, each network is behind a firewall/router. now what i want to do is be able to access one server on the second network from a computer on the first., but with the private ip address, (this... (2 Replies)
Discussion started by: norsk hedensk
2 Replies
2. Solaris
Hi All,
Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck.
Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies
3. Solaris
Hi All,
I have unplumbed one interface.
after that ifconfig -a shows that
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
... (7 Replies)
Discussion started by: jegaraman
7 Replies
4. Solaris
Probe-based IPMP active - active
Probe-based IPMP active - passive
Link-based only active -standby
????
What are differences between
Probe-based IPMP active - passive anddd
Link-based only active -standby
???!!!
For example in active active probe-based IPMP there are
lets... (6 Replies)
Discussion started by: samar
6 Replies
5. Solaris
Guide me in setting up IPMP on solaris 10 box .
my system has 2 physical interface
bge0 - not used
bge1 - 10.10.10.10
bge1:1 - 10.10.10.11
please guide , how can i implement IPMP on this server , how many additional test ip is required ? , as 2 ip's are configured on bge1 interface ,... (3 Replies)
Discussion started by: skamal4u
3 Replies
6. Solaris
Hi all,
Currently i got a server which had two interface. I had study the <SystemAdministration Guide: IP> but still donno what is the correct step to configure it. Can u all help me on it? thanks
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index... (6 Replies)
Discussion started by: SmartAntz
6 Replies
7. Solaris
Dear All,
I have configured IPMP in one of my SUN machine which is having solros 9 version. I have updated all files like /etc/hosts,/etc/hostname.ce0 and /etc/hostname.ce1 and rebooted the server. But IP's are not mounted which i have given in /etc/hosts file.
Please find the below ifconfig... (6 Replies)
Discussion started by: lbreddy
6 Replies
8. Solaris
Please tell me how to configure IPMP in vmware
what is the basic working concept of IPMP.
please help me (1 Reply)
Discussion started by: sijocg
1 Replies
9. Solaris
Hi all
i had two interface
ce0 and ce5
but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it?
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies
10. Solaris
Hi
I would like to know whether we can configure link based IPMP in private connectivity in Oracle RAC
Regarsd
---------- Post updated at 04:35 PM ---------- Previous update was at 04:27 PM ----------
Here I am taking about in case of private connectivity through cross cable (6 Replies)
Discussion started by: sb200
6 Replies
LEARN ABOUT SUSE
tc-matchall
Match-all classifier in tc(8) Linux Match-all classifier in tc(8)
NAME
matchall - traffic control filter that matches every packet
SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ]
DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
skip_sw
Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter-
face, operation will fail.
skip_hw
Do not process filter by hardware.
EXAMPLES
To create ingress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that
mirrors the packets to device eth2.
To create egress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle 1: root prio
tc filter add dev eth1 parent 1:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a
matchall filters on it that mirrors the packets to device eth2.
To sample one of every 100 packets flowing into interface eth0 to psample group 12:
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: matchall
action sample rate 100 group 12
SEE ALSO
tc(8),
iproute2 21 Oct 2015 Match-all classifier in tc(8)