Sponsored Content
Special Forums Cybersecurity Configure iptables to allows list of MAC address Post 302526380 by DGPickett on Tuesday 31st of May 2011 10:58:08 AM
Old 05-31-2011
I suppose you could ping each subnet's broadcast, collect IPs, ping each and then dump the arp cache for MACs.
 

8 More Discussions You Might Find Interesting

1. IP Networking

trying to configure DNS address in Solaris

hi to all. I'm trying to use the sendmail command to generate some reports and I cant use it. The mails i try to send simply won't go out, instead I receive a response from the system sayng that the host is unknown. I think the problem is in the DNS configuration (or the IMAP/SMTP servers). ... (3 Replies)
Discussion started by: ldrojasm
3 Replies

2. IP Networking

How to Achive IP address through MAC(Ethernet) address

Hi sir, i want to make such programe which takes MAC(Ethernet) address of any host & give me its IP address....... but i'm nt getting that how i can pass the MAC address to Frame........ Please give me an idea for making such program... Thanks & regards Krishna (3 Replies)
Discussion started by: krishnacins
3 Replies

3. Solaris

How to Configure a Static Ip Address

Hello friend, I am new in UNIX, but I want to learn a lot Well I have a problem to try to configure my PC with a static IP Address (IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1) (DNS 200.48.225.130 and 200.48.225.146). where are the file that I must be change? The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies

4. IP Networking

Tracing a MAC address to IP address: Solaris

Hi there I lost connectivity to one of our remote systems and when I checked the messages log I found the following: Aug 10 23:42:34 host xntpd: time reset (step) 1.681729 s Aug 16 13:20:51 host ip: WARNING: node "mac address" is using our IP address x.x.x.x on aggr1 Aug 16 13:20:51 host... (9 Replies)
Discussion started by: notreallyhere
9 Replies

5. Shell Programming and Scripting

configure from address in mailx command

Hi, I need to configure customized from address in mailx command. Can you pls tell me the option for configuring from address. Thanks Latika (9 Replies)
Discussion started by: latika
9 Replies

6. Solaris

to configure ip address

i have installed solaris 10 on my vmware..please tell me how i can configure ip addres and other things so that i can use internet (2 Replies)
Discussion started by: shekhar_4_u
2 Replies

7. IP Networking

Configure squid to listen on any IP address with port 80

Hi, I am trying to configure a transparent squid cache. When I try to use the below option in squid.conf, squid listens on port 80 only for the IP address configured on the system's interface. http_port 80 transparent But I want squid to accept connections for any IP address on port 80.... (3 Replies)
Discussion started by: Learner32
3 Replies

8. IP Networking

MAC Address - Four Interfaces with the same MAC Address

four interfaces with ifconfig all interfaces have the same mac. If is not set for unique. but it still works. what difference does it make to have all macs the same or different? (4 Replies)
Discussion started by: rrodgers
4 Replies
OCF_PACEMAKER_PING(7)					      Pacemaker Configuration					     OCF_PACEMAKER_PING(7)

NAME
ocf_pacemaker_ping - node connectivity SYNOPSIS
[OCF_RESKEY_pidfile=string] [OCF_RESKEY_dampen=integer] [OCF_RESKEY_name=string] [OCF_RESKEY_multiplier=integer] [OCF_RESKEY_host_list=string] [OCF_RESKEY_attempts=integer] [OCF_RESKEY_timeout=integer] [OCF_RESKEY_options=string] [OCF_RESKEY_debug=string] ping [start | stop | reload | monitor | meta-data | validate-all] DESCRIPTION
Every time the monitor action is run, this resource agent records (in the CIB) the current number of ping nodes the host can connect to. It is essentially the same as pingd except that it uses the system ping tool to obtain the results. SUPPORTED PARAMETERS
OCF_RESKEY_pidfile = string [/var/run//ping-default] PID file OCF_RESKEY_dampen = integer [5s] Dampening interval The time to wait (dampening) further changes occur OCF_RESKEY_name = string [pingd] Attribute name The name of the attributes to set. This is the name to be used in the constraints. OCF_RESKEY_multiplier = integer [] Value multiplier The number by which to multiply the number of connected ping nodes by OCF_RESKEY_host_list = string [] Host list The list of ping nodes to count. Defaults to all configured ping nodes. Rarely needs to be specified. OCF_RESKEY_attempts = integer [2] no. of ping attempts Number of ping attempts, per host, before declaring it dead OCF_RESKEY_timeout = integer [2] ping timeout in seconds How long, in seconds, to wait before declaring a ping lost OCF_RESKEY_options = string [] Extra Options A catch all for any other options that need to be passed to ping. OCF_RESKEY_debug = string [false] Verbose logging Enables to use default attrd_updater verbose logging on every call. AUTHOR
Andrew Beekhof <andrew@beekhof.net> Author. Pacemaker Configuration 07/05/2010 OCF_PACEMAKER_PING(7)
All times are GMT -4. The time now is 07:30 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy