05-22-2011
Actually I have not only resetsc, but I have also upgraded the entire firmware. I'm still getting the error message repeatedly
10 More Discussions You Might Find Interesting
1. Solaris
I recently got this new old server from a friend. I just installed a fresh version of Solaris 10 on it. I have put a static IP of 192.168.100.10 the server. Their is no subnetting scheme on the network. And I made the hostname "SunServ." And I also changed the folder "/etc/inet/hosts" because I... (4 Replies)
Discussion started by: louisd11
4 Replies
2. Solaris
Hi all,
I am getting the below error on Solaris sunfire v245 server
Error: can not display this video mode
optimum resolution 1024x768 60Hz
i am not able to resolve this .plz help me out ? (1 Reply)
Discussion started by: saurabh84g
1 Replies
3. Solaris
Hi all,
I have a T2000 server which does not seem to respond when I power it on. Looking on the console I see the following:
SC Alert: Host Power Failure: MB_DC_POK Fault
SC Alert: Host system poweron failed due to fault at MB/FF_POK.
SC Alert: VOLTAGE_SENSOR at MB/V_VCORE has exceeded... (4 Replies)
Discussion started by: jambalaya
4 Replies
4. Solaris
Hi,
I have a root with hardware RAID on c0t0d0 and c0t2d0. I would like to set the boot device sequence in OBP for both hdds.
I have checked in ls -l /dev/rdsk/ for the path of c0t2d0 but it does not exist. Can anyone shed some lights on this?
AVAILABLE DISK SELECTIONS:
0.... (12 Replies)
Discussion started by: honmin
12 Replies
5. Solaris
Hi Guyz,
I recently downloaded sol-10-u6-ga1-sparc-dvd.iso from Sun. I burned the disk as cd .iso.
When trying to boot at the ok> boot cdrom
i get the following error:
-----------------------------------------------------------------------
Boot device:... (2 Replies)
Discussion started by: Mwamba
2 Replies
6. Solaris
Hi all!
I've a machine - SunFire V890, it've been failed by OS error for 2 weeks ago, and now, I must reinstall OS (Solaris 10 2009), the progress was successful, but when I reboot, it displayed the error like :
Error -256: Last trap memory ... access aligned
Error -256: Last trap memory... (1 Reply)
Discussion started by: trantuananh24hg
1 Replies
7. Solaris
I work with a network management tool, which, for various reasons, is installed on a solaris server.This is a Sunfire T2000 server with 16 CPUs and 8GB of RAM. I have installed a Solaris 10 ZFS and 8GB swap. From the beginning I had problems with memory occupation that it rises progressively to 95%... (4 Replies)
Discussion started by: drusa79
4 Replies
8. Hardware
Recently the rear fan assembly of one of our T2000 servers went faulty. I could replace it immediately with the one from a currently powered off standby machine. But now this one has to be replaced.
So I got a quote from our supplier who charges EUR 776 for a new spare part or EUR 405 (all... (0 Replies)
Discussion started by: hergp
0 Replies
9. Solaris
I got a Power supply failure. I replaced the power supply and still got the error.
Any ideas on what I should try next? (1 Reply)
Discussion started by: 642fiddi
1 Replies
10. Hardware
I've recently bought an SunFire V245.
2x 2.5ghz x64
4gb ram
4x 73gb sas hdd
and... an blinking 'Identifior led' (white) with 'Service led' (amber) simultaneously.
It boots for +- 5 secs and then the error occurd.
Things done:
Removed all hdd.
Switched cpu
Switched/removed ram... (2 Replies)
Discussion started by: niswier2222
2 Replies
LEARN ABOUT DEBIAN
ift-extract
I2M19058(1) GNU Info I2M19058(1)
NAME
ift-extract.info - ift-extract.info
Built-in iSight firmware extractor and patcher
ift-extract extract the Built-in iSight firmware from Apple driver and patch it to avoid some bugs in it. The firmware is then ready to get
loaded into the chip using ift-load.
* Menu:
Finding the Apple driver: see "Driver"
Command line options: see "Options"
See also "Copying"
1 Finding the Apple driver
ift-extract extract Built-in iSight firmware from Apple iSight driver. This driver is located at
/System/Library/Extensions/IOUSBFamily.kext/Contents/PlugIns/AppleUSBVideoSupport.kext/Contents/MacOS/AppleUSBVideoSupport on your Mac OS X
root partition.
There is several version of this driver depending on driver version or host architecture (PowerPC or x86). Thus, ift-extract must determine
know the variant of the driver in order to properly extract the firmware.
Any AppleUSBVideoSupport file starting with those shipped with iMac G5 iSight must work. If not, please report unknown AppleUSBVideoSupport
at bugreport mail address with machine type and OS X version.
2 Command line options
`-a' `--apple-driver' Apple driver filename where to extract the firmware.
`-d' `--output-directory' The directory where to output the firmware. Defaults to /lib/firmware.
`-f' `--output-filename' The output firmware name. Defaults to isight.fw
`-?' `--help' Shows option help and quit.
Since ift-extract defaults to output the firmware to /lib/firmware/isight.fw, ensure you have the right to do so.
3 Copying
isight-firmware-tools is a project developped by A~Xtienne Bersac based on the work of Ronald S. Bultje, Johannes Berg and Ivan N. Zlatev.
This manual has been written by A~Xtienne Bersac.
Copyright (C) 2007 A~Xtienne Bersac <bersace@gmail.com>
perl v5.14.2 2012-01-09 I2M19058(1)