05-14-2011
It means that GRUB2 detected an error during boot and cannot pass control to the selected kernel because of a grub.cfg error and thus it reverted to rescue mode.
See the troubleshooting section of this guide:
https://help.ubuntu.com/community/Grub2
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed Linux 7.2 on a IBM xseries 235 server with 5 scsi hard drives and ServerRaid-5i Ultra320 scsi controller.
I started my installation by configuring the raid controller. I created 2 arrays, raid 1 and raid5. I then proceeded to install Linux and load the drivers.
After the... (2 Replies)
Discussion started by: cstovall
2 Replies
2. UNIX for Dummies Questions & Answers
Hi!
I got some serious problems with booting the computer. When started it prints GRUB GRUB GRUB all over the screen. tchan on #grub tried to help me but with no result. Here is the log.
Mabey there is something that we have missed?:confused: (3 Replies)
Discussion started by: Barfly.se
3 Replies
3. Red Hat
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Discussion started by: hassan2
7 Replies
4. UNIX for Dummies Questions & Answers
Hi, I installed solaris 10 a few weeks ago. It was working fine during the past two weeks. However, now when I start to load to the drive, I get this problem:
The BIOS screen comes up like normal, then screen goes blank and a message "Grub loading stage 2" flashes real quick then the computer... (1 Reply)
Discussion started by: moesays
1 Replies
5. UNIX for Dummies Questions & Answers
Hello,
I'm working on a x86 machine with 3 disks installed. I need to boot from disk to disk, but I cannot figure out how to do this using Grub. The O/S is Solaris 10 and grub version is 0.95
Can anyone give me any help with this?
Thanks,
James. (0 Replies)
Discussion started by: eeijmae
0 Replies
6. Solaris
Hi everyone
I have a problem. My configuration is as follows:
Sun 280R server
2 x internal disks
3 x state databases on disk 1
3 x state databases on disk 2
Disk 1 was giving errors, so I cleared the mirrors on it, deleted the state databases and replaced the disk. Before attaching... (5 Replies)
Discussion started by: soliberus
5 Replies
7. UNIX for Advanced & Expert Users
Hello,
I am using debian-5.0.0(lenny) . I installed windows xp(a hacked version) on a usb stick. this stick works perfectly well and boots off a windows system successfully.
but on linux it is finding problems to do so.
So I finally decided to put a grub entry to boot off the usb HDD.
... (8 Replies)
Discussion started by: gaurav1086
8 Replies
8. Solaris
Hi,
i am running an old Opensolaris 5.11 snv_111b on an x86 server. After almost 4 years of successful service, last night out of the blue started to refuse all connections to it's services, ssh, http,etc. The only visible solution at that time was a restart. But now instead of booting the... (2 Replies)
Discussion started by: d_oilen
2 Replies
9. Solaris
Hi Solaris 10 Experts,
I am wondering what is the correct syntax to edit in Grub when trying to specify the local ZFS boot disk while booting up from a Solaris 10 x86 64bits DVD installation disk. In other word, I try to boot up from local disk without removing the Solaris installation disk... (0 Replies)
Discussion started by: gjackson123
0 Replies
10. UNIX for Beginners Questions & Answers
Hi, someone knows how can I boot my OS or cdrom from a Grub Minimal_Bash? :confused: sorry, I´m a dummy
I explain, when I start loading the OS, I get errors, and ends up in the grub bash. This is the minimal_bash and I have no idea of any command. It tells me "unknow partition". The problem is... (0 Replies)
Discussion started by: veravera
0 Replies
LEARN ABOUT REDHAT
what-patch
WHAT-PATCH(1) General Commands Manual WHAT-PATCH(1)
NAME
what-patch - detect which patch system a Debian package uses
SYNOPSIS
what-patch [options]
DESCRIPTION
what-patch examines the debian/rules file to determine which patch system the Debian package is using.
what-patch should be run from the root directory of the Debian source package.
OPTIONS
Listed below are the command line options for what-patch:
-h, --help
Display a help message and exit.
-v Enable verbose mode. This will include the listing of any files modified outside or the debian/ directory and report any additional
details about the patch system if available.
AUTHORS
what-patch was written by Kees Cook <kees@ubuntu.com>, Siegfried-A. Gevatter <rainct@ubuntu.com>, and Daniel Hahler <ubuntu@thequod.de>,
among others. This manual page was written by Jonathan Patrick Davies <jpds@ubuntu.com>.
Both are released under the GNU General Public License, version 3 or later.
SEE ALSO
The Ubuntu MOTU team has some documentation about patch systems at the Ubuntu wiki: https://wiki.ubuntu.com/PackagingGuide/PatchSystems
cdbs-edit-patch(1), dbs-edit-patch(1), dpatch-edit-patch(1)
DEBIAN
Debian Utilities WHAT-PATCH(1)