05-14-2011
It means that GRUB2 detected an error during boot and cannot pass control to the selected kernel because of a grub.cfg error and thus it reverted to rescue mode.
See the troubleshooting section of this guide:
https://help.ubuntu.com/community/Grub2
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed Linux 7.2 on a IBM xseries 235 server with 5 scsi hard drives and ServerRaid-5i Ultra320 scsi controller.
I started my installation by configuring the raid controller. I created 2 arrays, raid 1 and raid5. I then proceeded to install Linux and load the drivers.
After the... (2 Replies)
Discussion started by: cstovall
2 Replies
2. UNIX for Dummies Questions & Answers
Hi!
I got some serious problems with booting the computer. When started it prints GRUB GRUB GRUB all over the screen. tchan on #grub tried to help me but with no result. Here is the log.
Mabey there is something that we have missed?:confused: (3 Replies)
Discussion started by: Barfly.se
3 Replies
3. Red Hat
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Discussion started by: hassan2
7 Replies
4. UNIX for Dummies Questions & Answers
Hi, I installed solaris 10 a few weeks ago. It was working fine during the past two weeks. However, now when I start to load to the drive, I get this problem:
The BIOS screen comes up like normal, then screen goes blank and a message "Grub loading stage 2" flashes real quick then the computer... (1 Reply)
Discussion started by: moesays
1 Replies
5. UNIX for Dummies Questions & Answers
Hello,
I'm working on a x86 machine with 3 disks installed. I need to boot from disk to disk, but I cannot figure out how to do this using Grub. The O/S is Solaris 10 and grub version is 0.95
Can anyone give me any help with this?
Thanks,
James. (0 Replies)
Discussion started by: eeijmae
0 Replies
6. Solaris
Hi everyone
I have a problem. My configuration is as follows:
Sun 280R server
2 x internal disks
3 x state databases on disk 1
3 x state databases on disk 2
Disk 1 was giving errors, so I cleared the mirrors on it, deleted the state databases and replaced the disk. Before attaching... (5 Replies)
Discussion started by: soliberus
5 Replies
7. UNIX for Advanced & Expert Users
Hello,
I am using debian-5.0.0(lenny) . I installed windows xp(a hacked version) on a usb stick. this stick works perfectly well and boots off a windows system successfully.
but on linux it is finding problems to do so.
So I finally decided to put a grub entry to boot off the usb HDD.
... (8 Replies)
Discussion started by: gaurav1086
8 Replies
8. Solaris
Hi,
i am running an old Opensolaris 5.11 snv_111b on an x86 server. After almost 4 years of successful service, last night out of the blue started to refuse all connections to it's services, ssh, http,etc. The only visible solution at that time was a restart. But now instead of booting the... (2 Replies)
Discussion started by: d_oilen
2 Replies
9. Solaris
Hi Solaris 10 Experts,
I am wondering what is the correct syntax to edit in Grub when trying to specify the local ZFS boot disk while booting up from a Solaris 10 x86 64bits DVD installation disk. In other word, I try to boot up from local disk without removing the Solaris installation disk... (0 Replies)
Discussion started by: gjackson123
0 Replies
10. UNIX for Beginners Questions & Answers
Hi, someone knows how can I boot my OS or cdrom from a Grub Minimal_Bash? :confused: sorry, I´m a dummy
I explain, when I start loading the OS, I get errors, and ends up in the grub bash. This is the minimal_bash and I have no idea of any command. It tells me "unknow partition". The problem is... (0 Replies)
Discussion started by: veravera
0 Replies
LEARN ABOUT DEBIAN
seeded-in-ubuntu
seeded-in-ubuntu(1) General Commands Manual seeded-in-ubuntu(1)
NAME
seeded-in-ubuntu - Determine whether a package is safe to upload during a freeze
SYNOPSIS
seeded-in-ubuntu [options] package...
DESCRIPTION
Lists all the current daily images containing the specified packages. Or whether the package is part of the supported seed.
If it isn't on an image, it should be safe to upload. During the final freeze, one should avoid packages in the supported seed too.
An index of the current manifests is downloaded from UbuntuWire.
OPTIONS
-b, --binary
The packages specified are binary packages. This is faster than source packages, as otherwise we must query LP to determine the
binary packages that every specified source package builds.
-u URL, --data-url=URL
URL for index of seeded packages. Default: UbuntuWire's service at http://qa.ubuntuwire.org/ubuntu-seeded-packages/seeded.json.gz.
-h, --help
Display a help message and exit
EXAMPLES
All the images that contain unity:
seeded-in-ubuntu -b unity
AUTHORS
seeded-in-ubuntu and this manpage were written by Stefano Rivera <stefanor@ubuntu.com>.
Both are released under the terms of the ISC License.
ubuntu-dev-tools December 2011 seeded-in-ubuntu(1)