05-13-2011
This User Gave Thanks to DukeNuke2 For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this:
dladm create aggr -d ce0 -d ce1 key
Do I need to... (1 Reply)
Discussion started by: hshapiro
1 Replies
2. Solaris
Hi, Anyone can help
My solaris 8 system has the following
/dev/null , /dev/tty and /dev/console
All permission are lrwxrwxrwx
Can this be change to a non-world write ??
any impact ?? (12 Replies)
Discussion started by: civic2005
12 Replies
3. Shell Programming and Scripting
dear all,,
can i showing ip address in the seven segment display?
#ifconfig eth0 192.168.1.1
in the seven segment display will show the ip address like i'm typing in the shell...if the ip address has changed in the shell then in the seven segment display change too...
plis help me about... (3 Replies)
Discussion started by: demhyt
3 Replies
4. Solaris
Hi,
I have freshly installed solaris 10 update 5 on my desktop, and during the installation, I specified a static IP address, gateway, netmask.
When I run "ifconfig rtls0" after the installation, I get the following message
#ifconfig rtls0
rtls0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4>... (8 Replies)
Discussion started by: krishisthere
8 Replies
5. Solaris
Greetings
how can i remove an interface from dladm?
i want to remove ce3 and ce4 which are not even plumbed but still shown in dladm output :(
dladm show-dev
ce0 link: unknown speed: 1000 Mbps duplex: full
ce1 link: unknown speed: 1000 Mbps duplex:... (3 Replies)
Discussion started by: kashif_islam
3 Replies
6. Solaris
hello everyone, I'm a new user and unix-beginner.
I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc
and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Discussion started by: kimj
12 Replies
7. Solaris
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies
8. Shell Programming and Scripting
Objective: To recreate the partitioning setup of /dev/sda on /dev/sdc
How would I parse the below information and initialize variables
(an array?) that can be used to build sgdisk commands in a script, regardless of the number of partitions?
Something along the lines of:
sgdisk -n... (12 Replies)
Discussion started by: RogerBaran
12 Replies
9. Red Hat
Hi,
Please suggest steps to change grub from /dev/sda to /dev/sdb, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
10. Solaris
Hi all,
I have never wondered where is the mapping of the link names to physical device path display under
dladm show-phys until today.
fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is... (1 Reply)
Discussion started by: javanoob
1 Replies
LEARN ABOUT CENTOS
prtdiag
prtdiag(1M) prtdiag(1M)
NAME
prtdiag - display system diagnostic information
SYNOPSIS
/usr/sbin/prtdiag [-v] [-l]
prtdiag displays system configuration and diagnostic information on sun4u and sun4v systems.
The diagnostic information lists any failed field replaceable units (FRUs) in the system.
The interface, output, and location in the directory hierarchy for prtdiag are uncommitted and subject to change in future releases.
prtdiag does not display diagnostic information and environmental status when executed on the Sun Enterprise 10000 server. See the
/var/opt/SUNWssp/adm/${SUNW_HOSTNAME}/messages file on the system service processor (SSP) to obtain such information for this server.
The following options are supported:
-l Log output. If failures or errors exist in the system, output this information to syslogd(1M) only.
-v Verbose mode. Displays the time of the most recent AC Power failure, and the most recent hardware fatal error information, and (if
applicable) environmental status. The hardware fatal error information is useful to repair and manufacturing for detailed diagnos-
tics of FRUs.
The following exit values are returned:
0 No failures or errors are detected in the system.
1 Failures or errors are detected in the system.
2 An internal prtdiag error occurred, for example, out of memory.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWkvm |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable* |
+-----------------------------+-----------------------------+
*The output is unstable.
modinfo(1M), prtconf(1M), psrinfo(1M), sysdef(1M), syslogd(1M), attributes(5), openprom(7D)
NOTES
Not all diagnostic and system information is available on every Solaris platforn, and therefore cannot be displayed by prtdiag. On those
platforms, further information can be obtained from the System Controller.
29 Aug 2005 prtdiag(1M)