Ok, I found a solution and let's hope that it is permanent and the error doesn't happen again:
The steps to be taken was:
1) umount -t flashcopy
2) varyoffvg flashcopyvg
3) rmdev -dl hdisk10;rmdev -dl hdisk11; rmdev -dl hdisk19
4) cfgmgr
5) varyonvg flashcopyvg
6) mount -t flashcopy
The configuration of the hdisks was firstly like:
Then it changed to:
and hdisk19 had the same PVID as hdisk8.
After the 6 steps above the situation is as before.
Does anyone have an idea what this means? hdisk10 is part of vg1. (vg1 has 11 hdisks)
I get this msg every morning @ 5:04 CST
This is the orignal message:
A PROBLEM WAS DETECTED ON Fri Aug 17 03:02:09 PDT 2001 801014
The Service Request Number(s)/Probable Cause or... (2 Replies)
Hi
We are running AIX5.3 on pseries 570. We have IBM ESS SAN stroage attached. We need to kick off flashcopy backups on the SAN. I have installed the CLI software but am missing a fileset. ibm2105esscli.rte or ibm2105cli.rte
This fileset contains the commands that can be issued from AIX to... (1 Reply)
When I list the PV's using lspv i see both vpath and hdisk names being listed. I got the info that each vpath is configured for 4 hdisks. Problem is I am not able to add either the hard disks in vpath to the existing non-rootvg. ? need to know the basics of vpath .. (4 Replies)
Hi,
in an environment with svc's and ds8xxx wat disk algorithm should be used and what is the difference here:
I can set the algorithm to Load_balance and to Round_robin (see output below).
some info:
hdisk3 ******** MPIO FC 2145
devices.sddpcm.53.rte 2.2.0.0 COMMITTED ... (1 Reply)
Hello,
Does anyone know how to copy SAN Storage logical disks from IBM TotalStorage Software.
I have a SAN Logical Disk of 200GB mounted on my AIX LPAR_1 via fibre channel fcs0
I would like to make an exact copy of the SAN Logical Disk from IBM totalStorage and mount it on AIX LPAR_2
... (4 Replies)
How do you create a dummy hdisk with AIX 6.1? In previous versions, I've used this and works, but now I get this error.
hostname:/:# mkdev -l hdisk57 -c disk -t osdisk -s scsi -p fscsi0 -w 0,10 -d
Method error (/etc/methods/define):
0514-022 The specified connection is not valid.
Any... (2 Replies)
Hi,
Planning to implement script to fetch whether the hdisks are in proper sequence. Need output for incorrect sequence
Correct
#lspv
hdisk0
hdisk1
hdisk2
::::::::::::
hdisk5
Incorrect sequence
#lspv
hdisk0
hdisk6
hdisk7
hdisk10
Any idea pls share (2 Replies)
Some storage/disks have been added to an existing AIX 6.1 server. The admin sent me the list of hdisk#'s for the new disks, but I need the corresponding rhdisk# for the same hdisk. (I know from past experience that the rhdisk that maps to an hdisk is not always the same number. For instance,... (5 Replies)
Discussion started by: sbrower
5 Replies
LEARN ABOUT MOJAVE
locale::codes::langext
Locale::Codes::LangExt(3pm) Perl Programmers Reference Guide Locale::Codes::LangExt(3pm)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangExt(3pm)