04-27-2011
Adding robot and drives
Hi All
Im running veritas netbackup 6.5.5, on MWindows 2003 master server.
Ive just added a Quantum PX500 with 2 drives, the problem im facing is that now under the storage unit tab on console all the storage unit types for NDMP have the new robot listed and not the original one. The set up i need is to have the old robot TLD0 listed.
Can anyone help, the robot and drives were added via Configure storage devices Wizard.. The original robot is a ADIC 500 8 drive library.
6 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
2. Filesystems, Disks and Memory
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies
3. Solaris
Hello, I have checked in here as I dont have enough experience as Solaris Admin. My Solaris seems to boot ok on a HP Proliant DL380 G6 server
The release is 5.10, the kernel ID is Generic_137138-09.
It was installed after creating one logical drive type RAID1, size 300GB.
Now 2 further... (2 Replies)
Discussion started by: fogarino
2 Replies
4. Solaris
hi,
i am using Solaris 8 on a sparc box and already have 4 tape drives in a backup libaray attached to my unix server. we have recently added 2 new tape drives to the libaray and now want to get unix to see them. have it working in windows.
how do i scan for new hardware and add theses new... (5 Replies)
Discussion started by: dshakey
5 Replies
5. Solaris
I need to add two new hard drives of 300 GB capacity to a SunSPARC T5440 server. The server currently has two hard drives of 146 GB each.
How do I add the new drives to the existing UFS?
What are the procedures involved in setting this server with the new hard drives? I am very new to Solaris... (6 Replies)
Discussion started by: ramatnmcc
6 Replies
6. Hardware
Normally I'm not into kits, but I thought my wife would enjoy this one since she is a big fan of robots and droids on StarWars!
We are done with the basic mechanical assembly and starting on the electronics assembly today.
The robot's "brain" consists of three levels. The Arduino board, on... (5 Replies)
Discussion started by: Neo
5 Replies
LEARN ABOUT DEBIAN
robot-pmaptest
robot-pmaptest(1) General Commands Manual robot-pmaptest(1)
NAME
robot-pmaptest - occupancy grid map creation tool
SYNOPSIS
robot-pmaptest [options] <logfilename>
DESCRIPTION
robot-pmaptest is utility demonstrates the basic functionality of the pmap library and serves a handy mapping utility in its own right.
Given a Player logfile containing odometry and laser data, robot-pmaptest will produce an occupancy grid map of the environment.
OPTIONS
-g disable the GUI (run in console mode only).
--range_max range
maximum effective range for the laser in meter (default: range saved in logfile).
--position_index index
index of odometry device in logfile (defualt: 0).
--laser_index index
index of laser device in logfile (default: 0).
--num_samples number
number of samples in particle filter (default: 200).
--resample_interval number
number of scans between resampling steps.
--resample_sigma width
width of resampling gaussian.
--num_cycles number
number of optimization cycles in the fine phase (default: 100).
--robot_x position
initial position of the robot on the x-axis.
--robot_y position
initial position of the robot on the y-axis.
--robot_rot rotation
initial rotation of the robot in degrees.
--grid_width width
width of the grid in meters (default: 64.0).
--grid_height height
height of the grid in meters (default: 48.0).
--grid_scale scale
scale of the grid in meters per cell (default: 0.10).
--laser_x position
position of the laser scanner on the robot.
--laser_rot rotation
rotation of the laser scanner on the robot in degrees.
--robot_hostname hostname
the hostname of the robot to verify in the logfile.
--robot_hostname hostname
the hostname of the robot to verify in the logfile.
--skip time
amount of time to skip between log entries.
--range_resresolution
resolution of the laser (only used inlodo, not lodo2 which is currentlyused).
--action_model_xx factor
believe factors in the change of the robot's pose.
--action_model_rx factor
believe factors in the change of the robot's pose.
--action_model_rr factor
believe factors in the change of the robot's pose.
AUTHOR
Player was written by Brian Gerkey <gerkey@users.sourceforge.net> and contributors. This manual page was written by Daniel Hess for the
Debian Project.
SEE ALSO
The HTML documentation in /usr/share/doc/player/html of the robot-player-doc package. robot-playervcr(1)
Player May 2009 robot-pmaptest(1)