Why to plumb every interface when you can plumb just a new one ?
Beyond the fact it's Solaris 9 so dladm isn't available as DukeNuke2 already point out, what's wrong with plumbing all interfaces ?
Quote:
and then NIC will be configured with DHCP if you have one on your network.
This is incorrect. The interface doesn't automagically configure itself with DHCP. Moreover, it will will be lost at next reboot if nothing is done to avoid that ...
All,
I see that there are 2 nic card available . How can I know all the details about these 2 nic cards.
-rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0
-rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2
please let me know
thanks
-prasad (4 Replies)
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Hi all,
I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me.... (5 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT PHP
dhcpmgr
dhcpmgr(1M) System Administration Commands dhcpmgr(1M)NAME
dhcpmgr - graphical interface for managing DHCP service
SYNOPSIS
/usr/sadm/admin/bin/dhcpmgr
DESCRIPTION
dhcpmgr is a graphical user interface which enables you to manage the Dynamic Host Configuration Protocol (DHCP) service on the local sys-
tem. It performs the functions of the dhcpconfig, dhtadm, and pntadm command line utilities. You must be root to use dhcpmgr. The dhcpmgr
Help, available from the Help menu, contains detailed information about using the tool.
USAGE
You can perform the following tasks using dhcpmgr:
Configure DHCP service
Use dhcpmgr to configure the DHCP daemon as a DHCP server, and select the data store to use for storing network configuration tables..
Configure BOOTP relay service
Use dhcpmgr to configure the DHCP daemon as a BOOTP relay.
Manage DHCP or BOOTP relay service
Use dhcpmgr to start, stop, enable, disable or unconfigure the DHCP service or BOOTP relay service, or change DHCP server parameters.
Manage DHCP addresses
Use dhcpmgr to add, modify, or delete IP addresses leased by the DHCP service.
Manage DHCP macros
Use dhcpmgr to add, modify or delete macros used to supply configuration parameters to DHCP clients.
Manage DHCP options
Use dhcpmgr to add, modify or delete options used to define parameters deliverable through DHCP.
Convert to a new DHCP data store
Use dhcpmgr to configure the DHCP server to use a different data store, and convert the DHCP data to the format used by the new data
store.
Move DHCP data to another server
Use dhcpmgr to export data from one Solaris DHCP server and import data onto another Solaris DHCP server.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
non-zero An error occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWdhcm |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO dhcpconfig(1M), dhtadm(1M), pntadm(1M), in.dhcpd(1M), dhcpsvc.conf(4), dhcp_network(4), dhcptab(4), attributes(5), dhcp(5), dhcp_modules(5)
Solaris DHCP Service Developer's Guide
System Administration Guide: IP Services
SunOS 5.10 13 Mar 2001 dhcpmgr(1M)